F 『
 E C F M E
 E E
 E 56-5B E
 E E

 (12) Put the upper cooling jacket (60) or (65) in position on the cowl opening actuator (50).

 (13) Put the lower cooling jacket (45) or (70) in position on the cowl opening actuator (50).

 (14) Install the two clamps (40) that attach the cooling jackets.

 (15) Put the flexible cooling hose (35) or (85) on the lower cooling jacket (45) or (70). Attach it with the clamp (25).

R (16) For the right hand cowl opening actuator only. Put the clamp (90) on R the flexible cooling hose (85).
 (17) Put the other end of the flexible cooling hose (35) or (85) on the inlet scoop (30) or (75). Attach it with the clamp (25).

 (18) TORQUE the clamp (25) to between 10 and 25 lbf.in (0.11 and 0.28 m.daN).

R (19) For the right hand cowl opening actuator only. Put the stud clip (95) R in the hole on the clamp (90) and install the nut (80).
 (20) TORQUE the nut (80) to between 22.127 and 26.553 lbf.in (0.25 and
 0.30 m.daN).
 5. Close-up
________
 Subtask 78-36-51-410-050
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the thrust reverser cowl doors (Ref. TASK 78-36-00-410-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR

 Subtask 78-36-51-440-050
 B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
 F 『 EEFF : ALL E Page 41378-36-51
 E E Nov 01/03 E E ECES E Subtask 78-36-51-410-051

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 C. Close Access
 (1) Remove the access platform(s).

 (2) Close the fan cowl doors (Ref. TASK 71-13-00-410-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR

 (3) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 41478-36-51
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 ACTUATOR - COWL OPENING (3003KM1,3003KM2) - INSPECTION/CHECK

____________________________________________________________
 TASK 78-36-51-210-041
 Visual Inspection of the Thrust Reverser Half Door Opening Actuator
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
 No specific access platform 1 m (3 ft. 3 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-005 Retracting the Slats on the Ground
 71-13-00-010-040 Opening of the Fan Cowl Doors
 71-13-00-410-040 Closing of the Fan Cowl Doors
 78-30-00-081-041 Make the Thrust Reverser Serviceable after

 Maintenance
 78-30-00-481-041 Make the Thrust Reverser Unserviceable for

 Maintenance
 78-36-00-010-040 Opening of the Thrust Reverser Doors
 78-36-00-410-040 Closing of the Thrust Reverser Doors

R  78-36-51-000-041 Removal of the Cowl Opening Actuator 78-36-51-400-041 Installation of the Thrust Reverser Half Door Opening
 Actuator
 IPC 78-36-51
 78-36-51-991-301 Fig. 601

 F 『 EEFF : ALL E Page 60178-36-51
 E E Feb 01/02 E E ECES E 3. Job Set-up

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

__________ Subtask 78-36-51-941-051
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 78-36-51-010-052
 B. Close Access
 (1) Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
 FOR 1000EM1
 437AL, 438AR
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(124)