(0.40 to 2.60 m.daN)
No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2245 *
finish paint EA4 blue 5991 (Ref. 70-30-00)
F 『 EEFF : ALL E Page A48178-31-49
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance 78-30-00-710-040 Thrust Reverser Hydraulic System Bleed Procedure 78-31-49-991-322 Fig. 421
3. Job Set-up
__________
Subtask 78-31-49-860-101
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the access platform is in position.
Subtask 78-31-49-010-158
B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
Subtask 78-31-49-040-146
C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
F 『 EEFF : ALL E Page A48278-31-49
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
4. Procedure
_________ (Ref. Fig. 421/TASK 78-31-49-991-322) Subtask 78-31-49-420-092
A. Installation of the Lower Swivel Joints
(1) Remove the protective covers from the hose and pipe ends.
(2) Connect the rod supply junction pipe and the lower rod supply hose to the swivel joint.
(3) TORQUE the coupling nuts to between 130 and 150 lbf.in (1.46 and 1.69 m.daN).
(4) Connect the head supply junction pipe and the lower head supply hose to the swivel joint.
(5) TORQUE the coupling nuts to between 235 and 260 lbf.in (2.65 and 2.93 m.daN).
(6) Attach the lower head shield to the forward frame with the bolts and the nuts.
(7) TORQUE the bolts to between 61 and 70 lbf.in (0.68 and 0.79 m.daN). NOTE : Apply a witness line of finish paint EA4 blue 5991 (Material
____ No. CP2245) on all nuts and connections after they are torqued.
5. Close-up
________ Subtask 78-31-49-440-097
A. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
F 『 EEFF : ALL E Page A48378-31-49
E E Feb 01/98 E E ECES E Subtask 78-31-49-410-109
F 『
E C F M E
E E
E 56-5B E
E E
B. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(3) Remove the access platform(s).
(4) Remove the warning notice(s). Subtask 78-31-49-710-077
C. Bleed the air from the thrust reverser hydraulic system. (Ref. TASK 78-30-00-710-040)
F 『 EEFF : ALL E Page A48478-31-49
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 78-31-49-000-007
Removal of the Interface Bracket, HCU Bracket and Hydraulic Line Middle Bracket
WARNING : WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU
_______
WORK ON PRESSURIZED SYSTEMS.
R WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______ R - FLUSH IT AWAY WITH CLEAN WATER R - GET MEDICAL AID.
CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______
ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(13)
