Maintenance
 78-30-00-481-041 Make the Thrust Reverser Unserviceable for

 Maintenance
 78-32-41-000-001 Removal of the Lower Blocker Door
 78-32-41-000-002 Removal of the Upper Blocker Door
 78-32-41-000-003 Removal of the Latch Fitting and Latch Back Plate
 78-32-41-000-004 Removal of the Kicker Plate from the Blocker Door

 F 『 EEFF : ALL E Page 60178-32-41
 E E Feb 01/98 E E ECES E -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

78-32-41-080-001 Removal of the Safety Sleeve from Blocker Door
 Actuator 78-32-41-400-001 Installation of the Lower Blocker Door 78-32-41-400-002 Installation of the Upper Blocker Door 78-32-41-400-003 Installation of the Latch Fitting and Latch Back
 Plate 78-32-41-400-004 Installation of the Kicker Plate from the Blocker Door 78-32-41-480-001 Installation of the Safety Sleeve on Blocker Door
 Actuator 78-32-41-820-001 Alignment of the Blocker Door 78-32-41-860-001 Manual Deployment of the Blocker Door 78-32-41-860-002 Manual Stowing of the Blocker Door 78-32-41-991-312 Fig. 601
 3. Job Set-up
__________
 Subtask 78-32-41-941-052
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 F 『 EEFF : ALL E Page 60278-32-41
 E E Feb 01/98 E E ECES E Subtask 78-32-41-010-051

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 B. Get Access
 (1) Open the fan cowl doors (Ref. TASK 71-13-00-010-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
 (2) Put the access platform in position. Subtask 78-32-41-040-052

 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041). Subtask 78-32-41-010-052

 D. Deploy the blocker door manually (Ref. TASK 78-32-41-860-001). Subtask 78-32-41-480-051

 E. Install the SAFETY SLEEVE - PIVOTING DOOR ACTUATOR (HIX3005) on the blocker door (Ref. TASK 78-32-41-480-001).
 F 『 EEFF : ALL E Page 60378-32-41
 E E Feb 01/98 E E ECES E 4. Procedure

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

_________
 (Ref. Fig. 601/TASK 78-32-41-991-312) Subtask 78-32-41-210-050
 A. Do a visual inspection of the blocker door as follows:
 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Examine the blocker door for:
 A. Delamination  1.5 in. (38.1 mm) maximum length.
 7.4 in. (188 mm) minimum distance from other delaminations, holes or cracks.
 Five delaminations maximum per blocker door. 
B. Abrasion  No carbon fiber damage permitted.

Monitor at "A" check
It is recommended that alldelaminations be repairedno later than "C" check.
If the delaminations arenot in the serviceablelimits, replace the blocker door.(Ref. TASK 78-32-41-000-001) or (Ref. TASK 78-32-41-000-002) and (Ref. TASK 78-32-41-400-001) or (Ref. TASK 78-32-41-400-002).
Monitor at "A" check.
 Seal surface damage (Paint and surface resin only) with aerodynamic tape (Material No. CP2517).
 Replace tape if peeled.
 F 『 EEFF : ALL E Page 60478-32-41
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Permissible Wear - Blocker Door
 Figure 601/TASK 78-32-41-991-312

 F 『 EEFF : ALL E Page 60578-32-41
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(75)