曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (2) Make sure that the work area is clean and clear of tool(s) and other items.
 Subtask 57-71-00-865-056
R  B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 21CE1, 22CE, 21CE3, 21CE2.
 Subtask 57-71-00-860-055 
R R  C. Aircraft Maintenance Configuration 
R R  (1) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever. 
R  (2) Retract the spoiler 1 (Ref. TASK 27-60-00-866-002). 
R  (3) Retract the flaps (Ref. TASK 27-50-00-866-009). 
R R  (4) On the servo-control, make sure that the pointer on the hex-head is opposite the letter 'O' (Operation) on the housing.
 Subtask 57-71-00-942-056
 D. Removal of the Equipment
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Remove the safety barriers.
 (3) Remove the warning notice(s).
 (4) Remove the access platform(s).
 (5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 

 SKINS AND PLATING - CLEANING/PAINTING_____________________________________
 TASK 57-71-11-100-001
 Cleaning and Painting of the Spoiler 1
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR. 
R R R R R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 NOTE : The clean/paint procedure is the same for all the spoilers.____
 1. Reason for the Job__________________
 Self Explanatory
 2. Job Set-up Information______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific No specific No specific No specific 98D27604000000 98D27803500001  safety barrierssoft brushvacuum cleanerwarning noticewarning noticeswash brush1 COLLAR-SAFETY, SPOILER2 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER

 

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-001 USA MIL-D-16791 TYPE I R DETERGENT (Ref. 20-31-00)
 Material No. 11-004  USA MIL-T-81533
 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
 (Ref. 20-31-00)

 Material No. 19-003  USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-60-00-866-002 Extension-Retraction of the Spoilers for Maintenance 29-10-00-864-003 Depressurize the Blue Hydraulic System 29-23-00-864-001 Depressurize the Green and Yellow Hydraulic Systems
 after Operation of the PTU
 29-24-00-864-001 Depressurize the Yellow Hydraulic System
 51-75-12-300-001 Repair of Major Paint Damage on Light Alloy and

 Composite Material
 51-75-12-300-002 Repair of Major Paint Damage on Steel Component
 51-75-12-300-003 Repair of Minor Paint Damage (Topcoat Only)

 3. Job Set-up
__________
 Subtask 57-71-11-941-053
 A. Safety Precautions
 (1)
 Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.

 (2)
 Put warning notices in the cockpit to tell persons not to operate the flaps or slats.

 (3)
 Put a warning notice on the HYD section of panel 40VU to tell persons not to pressurize the aircraft hydraulic systems.

 (4)
 Put the safety barriers in position.

 (6)
 Replace the cloth frequently to make sure that contamination is not put back on the surfaces.

 (7)
 Clean recesses and edges with the wash brush and CLEANING AGENTS (Material No. 11-004).

 (8)
 Do the procedure again until the areas are clean.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(98)