-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 3.0 m (9 ft. 10 in.)
R 98D27507541000 1 WRENCH - BEARING, FLAP TO CARRIAGE TRACK 2 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-54-62-000-001 Removal of the Outboard Flap
27-54-62-000-002 Removal of the Outboard Double-Slotted Flap
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
57-53-21-991-001 Fig. 401
**ON A/C 301-399,
57-53-21-991-001-A Fig. 401A
**ON A/C ALL
3. Job Set-up
__________
Subtask 57-53-21-941-050
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the slat/flap control lever.
(3)
Put warning notices in position to tell persons not to operate the slat/flap system.
Subtask 57-53-21-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-53-21-010-050
C. Get Access
(1) Put the access platform in position below the applicable outboard flap at zone 533 (633).
(2) Remove the applicable outboard flap (Ref. TASK 27-54-62-000-001). **ON A/C 301-399,
Subtask 57-53-21-010-050-A
C. Get Access
(1) Put the access platform in position below the applicable outboard flap at zone 533 (633).
(2) Remove the applicable outboard flap (Ref. TASK 27-54-62-000-002). **ON A/C ALL
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 401/TASK 57-53-21-991-001)
**ON A/C 301-399,
(Ref. Fig. 401A/TASK 57-53-21-991-001-A)
Flap Attachment Bearing - Location and Detail
Figure 401/TASK 57-53-21-991-001
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-21Page 404 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R Flap Attachment Bearing - Location and Detail R Figure 401A/TASK 57-53-21-991-001-A
R 1EFF : 301-399, 1 57-53-21Page 405 1 1 May 01/04 1 1 1CES 1
**ON A/C ALL
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-53-21-020-050
A. Removal of the Flap Attachment Bearing
(1)
Release the lockwasher (2).
(2)
Use the WRENCH - BEARING, FLAP TO CARRIAGE TRACK 2 (98D27507541000) to remove the locknut (1). Discard the locknut (1).
(3)
Remove and discard the lockwasher (2).
(4) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(37)
