-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 3.0 m (9 ft. 10 in.)
460005833 1 GROUND LOCK SLEEVE
460007280 1 GROUNDLOCK SLEEVE
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-14-400-001 Installation of the MLG Fixed Fairing Assembly (That
was Removed For Access Only) R 57-55-11-991-022 Fig. 416
3. Job Set-up
__________ Subtask 57-55-11-941-069
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(3)
On the panel 400VU:
-make sure that the landing-gear control-lever (6GA) is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gears.
Subtask 57-55-11-860-072
B. Get Access
(1)
Open the MLG doors (Ref. TASK 32-12-00-010-001).
(2)
Make sure that the GROUND LOCK SLEEVE (460005833) or the GROUNDLOCK SLEEVE (460007280) is installed on the applicable MLG lockstay actuator (Ref. TASK 32-00-00-481-001).
(3) Put the access platform in position at zone 733(743). Subtask 57-55-11-865-074
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
1EFF : 301-399, 1 57-55-11Page 484 1 1 Aug 01/04R 1 1 1CES 1
4. Procedure
_________
R (Ref. Fig. 416/TASK 57-55-11-991-022) Subtask 57-55-11-210-062
A. Preparation for Removal
(1)
Examine the area around the extension fairing (1) for the black painted lines.
(2)
If you cannot find the black painted lines, paint three black lines in the correct position (Ref. TASK 32-12-14-400-001).
Subtask 57-55-11-020-074
B. Removal of the Hinge 1A Extension Fairing.
(1)
Hold the extension fairing (1).
(2)
Remove the bolts (5), the washers (4), the bolt (3), and the washer (2).
(3)
Remove the extension fairing (1).
Hinge 1A Extension Fairing - Location and Detail R Figure 416/TASK 57-55-11-991-022
1EFF : 301-399, 1 57-55-11Page 486 1 1 Aug 01/04 1 1 1CES 1
TASK 57-55-11-400-006
Installation of the Hinge 1A Extension Fairing
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notices
No specific access platform 3.0 m (9 ft. 10 in.) R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft)
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護(hù)手冊 AMM WINGS 機翼5(74)
