R 4. Procedure_________
R (Ref. Fig. 409/TASK 57-55-11-991-010, 410/TASK 57-55-11-991-011, 411/TASK
R 57-55-11-991-013, 412/TASK 57-55-11-991-012)
R Subtask 57-55-11-420-077
R A. Preparation for Installation
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R (1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING
R AGENTS (Material No. 11-004) to clean the component interface and/or
R the adjacent area.
R (2) Do an inspection of the component interface and/or the adjacent area.
R (3) Make sure that the parts retained from the removed component are
R clean and in the correct condition.
R Subtask 57-55-11-420-069
R B. Installation of the Flap Track Fairing
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R (1) Install the adjusters (52) and make sure that they are adjusted fully
R into their mountings.
R (2) Align the movable fairing at the forward pivot, then install the
R splined fittings (53).
R Fairing Installation - Dimensions
R Figure 412/TASK 57-55-11-991-012
1EFF : 301-399, 1 57-55-11 Page 461
1 1 May 01/04
1 1
1CES 1
R (3) Lift the movable fairing:
R WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME_______
R DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
R NOTE : The weight of the fairing is approximately 18Kg (40lb).____
R (a) Align the control rod (45), with the flap lever and temporarily
R install the bolt (41), the bush (42) and the nut (43).
R (4) Install the bonding disc (7) and the bonding strap (6) with the bolt
R (9) and the nut (5) onto the fixed fairing (1).
R (5) Torque the nut (5) to between 3.5 and 4.5 m.daN (25.81 and 33.18
R lbf.ft).
R (6) Temporarily install the fixed fairing (1) with the bolts (2), (8) and
R (12).
R (7) Measure the dimension A, this must be between 7.5 mm (0.30 in.) and
R 9.5 mm (0.37 in.).
R (8) If the dimension A is not correct, remove the bolts (2), (8) and (12)
R and the fixed fairing (1), and continue as follows:
R (a) Calculate the quantity of packer(s) (19) to get the dimension A
R in limits.
R (b) Install the packer(s) (19) on the nut plate assembly.
R (c) Install the fixed fairing (1) with the bolts (2), (8) and (12).
R (d) Measure the dimension A again.
R (9) Align the movable fairing with the fixed fairing (1).
R (10) Measure the dimension 'E', at both sides of the pivot. The dimension
R must be between zero, +/- 1 mm (0.04 in.).
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(67)
