-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575329-01 Detailed Visual Inspection of Outboard Double Slotted Flap, Internal Support fitting at Track 3, Including Attachment Bracket, Drive Bracket and Attachment Structure, Internal and External, LH/RH
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific spark-proof lamp No specific warning notice No specific access platform 2.5 m (8 ft. 2 in.)
1EFF : 301-399, 1 57-53-00Page A676 1 1 Nov 01/04R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 57-55-11-000-004 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-004 Installation of the Flap Track Fairings Nos. 2, 3 and
4 ASRM 575300 (for corrective action) 57-53-00-991-029 Fig. 625
3. Job Set-up
__________
Subtask 57-53-00-941-082
A. Safety Precautions
(1)
Put a warning notice on the flap/slat control lever (panel 114VU) to tell persons not to operate the flaps.
(2)
Put the safety barriers in position.
Subtask 57-53-00-860-054
B. Aircraft Maintenance Configuration
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1) Fully extend the flaps (Ref. TASK 27-50-00-866-008).
1EFF : 301-399, 1 57-53-00Page A677 1 1 Nov 01/04R 1 1 1CES 1
(2) Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever on the panel 114VU.
Subtask 57-53-00-865-111
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
Subtask 57-53-00-010-076
D. Get Access
(1)
Put the access platform in position below the flap track 3 at zone 532(632).
(2)
Remove the applicable flap track fairings (Ref. TASK 57-55-11-000-004):
-
for the left wing, remove 532AT, 532CB
-
for the right wing, remove 632AT, 632CB.
(3)
Remove the applicable access panel in the bottom skin at track 3:
-
for the left wing, remove 587AB
-
for the right wing, remove 687AB.
(4)
Put the spark-proof lamp adjacent to the inspection area.
4. Procedure
_________
(Ref. Fig. 625/TASK 57-53-00-991-029)
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(9)
