-
there are no cracks or scores
-the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575300) for the
____
correct repair procedure.
5. Close-up
________
Subtask 57-53-00-410-078
A. Close Access
(1)
Remove the spark-proof lamp from the inspection area.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Install the applicable access panel in the bottom skin at track 4:
-
for the left wing, install 587BB
-
for the right wing, install 687BB.
1EFF : 301-399, 1 57-53-00Page A698 1 1 Nov 01/04R 1 1 1CES 1
(4) Install the applicable flap track fairing (Ref. TASK 57-55-11-400-004):
-for the left wing, install 533AT, 533CB
-for the right wing, install 633AT, 633CB. Subtask 57-53-00-865-118
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-53-00-860-061
C. Aircraft Maintenance Configuration
(1) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-53-00-942-082
D. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the safety barriers.
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : 301-399, 1 57-53-00Page A699 1 1 Nov 01/04R 1 1 1CES 1
TASK 57-53-00-220-016
R Special Detailed Inspection of Outboard Double-Slotted Flap, Internal Support Fitting at Track 4, Including Pendulum Support, Drive Bracket ....
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575333-02 R Special Detailed Inspection of Outboard Double-Slotted Flap, Internal R Support Fitting at Track 4, Including Pendulum Support, Drive Bracket and
Attachment Structure, Internal and External, LH/RH
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific spark-proof lamp
No specific warning notice
No specific access platform 2.5 m (8 ft. 2 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 57-55-11-000-004 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-004 Installation of the Flap Track Fairings Nos. 2, 3 and
4
R NTM 57-53-33 PART 9 ASRM 575300 (for corrective action) 57-53-00-991-033 Fig. 629
3. Job Set-up
__________
Subtask 57-53-00-941-086
A. Safety Precautions
(1)
Put a warning notice on the flap/slat control lever (panel 114VU) to tell persons not to operate the flaps.
(2)
Put the safety barriers in position.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(15)
