39.82 lbf.in).
(d)
Apply a bead of SEALANTS (Material No. 09-016) into the groove between the forward and aft fixed fairings.
(e)
Use CLEANING AGENTS (Material No. 11-026) and a plastic spatula, to make the bead smooth and level with the fairings.
Subtask 57-55-11-865-064
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-55-11-860-061
D. Aircraft Maintenance Configuration
(1)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(2)
Do a check of the flap track fairing lateral movement (Ref. TASK 57-55-11-200-001).
Subtask 57-55-11-710-050
E. Test
(1)
Do an Operational Test of the flap system (Ref. TASK 27-54-00-710-001).
(2)
Make sure that the movable-fairing operates correctly.
5. Close-up
________ Subtask 57-55-11-942-050
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-55-11Page 422 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(4)
Remove the warning notice(s).
(5)
Remove the safety barriers.
(6)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-55-11Page 423 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C ALL
TASK 57-55-11-010-001
To Lower the Flap Track No. 2 Movable Fairing for Access
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 3 m (9 ft. 10 in.)
98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-50-00-866-009 Retraction of the Flaps on the Ground
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
57-55-11-991-007 Fig. 406
**ON A/C 301-399,
57-55-11-991-007-A Fig. 406A
**ON A/C ALL
3. Job Set-up
__________
Subtask 57-55-11-941-061
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-55-11-860-059
B. Aircraft Maintenance Configuration
(1)
Make sure that the flaps are fully retracted (Ref. TASK 27-50-00-866-009).
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap control lever.
(3)
Put the access platform below the applicable flap track 2, zone 531 (631).
Subtask 57-55-11-865-068
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 406/TASK 57-55-11-991-007)
**ON A/C 301-399,
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(58)
