R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A657 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Outboard Flap
Figure 622A/TASK 57-53-00-991-024-A12 (SHEET 1)
R 1EFF : 106-149, 215-299, 401-499, 1 57-53-00Page A658 1 1 Aug 01/05 1 1 1CES 1
Outboard Flap
Figure 622A/TASK 57-53-00-991-024-A22 (SHEET 2)
R 1EFF : 106-149, 215-299, 401-499, 1 57-53-00Page A659 1 1 Aug 01/05 1 1 1CES 1 NOTE : If necessary, refer to the ASRM (Ref. ASRM 575300) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie.
5. Close-up
________
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-214,
Subtask 57-53-00-410-072
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A) cut to the correct dimensions, to make a new cover for the RH inspection hole.
(3)
Install the new cover on the RH inspection hole.
(4)
Install the leading edge panel 5 (Ref. TASK 27-54-62-400-003).
(5)
Install the flap track 4 fairing 533CB (633CB) and the access panel 533AT (633AT) (Ref. TASK 57-55-11-400-001).
R **ON A/C 106-149, 215-299, 401-499,
Subtask 57-53-00-410-072-A
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A) cut to the correct dimensions, to make a new cover(s) for the applicable inspection hole(s).
(3)
Install the new cover(s) on the applicable inspection hole(s).
(4)
Install the flap track 4 fairing 533CB (633CB) and the access panel 533AT (633AT) (Ref. TASK 57-55-11-400-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A660 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-53-00-865-102
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-53-00-860-124
C. Aircraft Maintenance Configuration
(1) Retract the flaps fully (Ref. TASK 27-50-00-866-009).
Subtask 57-53-00-942-075
D. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A661 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
**ON A/C 301-399,
TASK 57-53-00-210-001
Detailed Visual Inspection of Outboard Double Slotted Flap Inboard Rib, Including Interconnection Strut Attachment Bracket, Lever and Roller ....
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575327-01
Detailed Visual Inspection of Outboard Double Slotted Flap Inboard Rib,
Including Interconnection Strut Attachment Bracket, Lever and Roller,
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(5)
