(2)
Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A), cut to the correct dimensions, to make new covers for the inspection holes.
(3)
Install the new covers on the inspection holes.
(4)
Install the flap track 4 fairing 533CB (633CB) and the access panel 533AT (633AT) (Ref. TASK 57-55-11-400-004).
(5)
Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 57-53-00-865-138
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-53-00-860-127
C. Aircraft Maintenance Configuration
(1) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.
(2) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-53-00-942-092
D. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
**ON A/C ALL
TASK 57-53-00-220-023
Detailed Dimensional Check of the Joints that Attach the Flap to the Flap Carriage (Tracks 3 and 4)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Because the free movement of the outboard flap is more than that in TASK 27-54-00-200-003.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific access platform 2 m (6 ft. 7 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-54-62-000-001 Removal of the Outboard Flap 27-54-62-000-002 Removal of the Outboard Double-Slotted Flap 27-54-62-400-001 Installation of the Outboard Flap 27-54-62-400-002 Installation of the Outboard Double-Slotted Flap
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
57-53-00-991-044 Fig. 639
**ON A/C 301-399,
57-53-00-991-044-A Fig. 639A
**ON A/C ALL
3. Job Set-up
__________
Subtask 57-53-00-941-097
A. Safety Precautions
(1) Put a warning notice on the flap/slat control lever (panel 114VU) to tell persons not to operate the flaps.
(2) Put the safety barriers in position. R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-53-00-010-093
B. Get Access
(1)
Put the access platform below the applicable zone 575 or 675.
(2)
Remove the outboard flap. (Ref. TASK 27-54-62-000-001)
**ON A/C 301-399,
Subtask 57-53-00-010-093-A
B. Get Access
(1) Put the access platform below the applicable zone 575 or 675.
(2) Remove the outboard flap. (Ref. TASK 27-54-62-000-002)
**ON A/C ALL
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(29)
