SEE B
HANGER
RETRACT ACTUATOR 16. VALVE BLEED E BOLT
WALKING BEAM
E
NUT
FWD
21. THICK NYLON WASHER B
1. ACTUATOR HEAD
HANGER WASHER NUT FITTING GREASE WALKING BEAM 2. 19. 18. 17. 30. 20. ANTIROTATION BOLT 22. THIN NYLON WASHER 19. WASHER NUT HANGER WALKING BEAM 2. 17. 18,
LUBE INSERT 29.
BOLT3.
3 NUT WASHER 28. 27. 26. DIRECTION OF INSTALLATION IS OPTIONAL WIDE SPACER E-E 3 25. SPACER NUT THREADED SPACER 24. 23. SPACER NARROW
Figure 401 (Sheet 4) Wing Landing Gear Actuator Installation
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-32-01
ALL ú ú 01 Page 406 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE C
SEE D
FWD
C
31. LUBE INSERT
39. LOCKBOLT 5. ATTACH BOLT ROD END ACTUATOR
38. WASHER
37. NUT
32. SPACER 33. WASHER 35. NUT 36. WASHER 33. WASHER 32. SPACER
34. SLEEVE
D
Figure 401 (Sheet 5) Wing Landing Gear Actuator Installation
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-32-01
ALL ú ú 01 Page 407 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(2) S 024-032Disconnect the hydraulic hoses from the actuator.
(3) S 024-033Remove the hose clamps (6) from the clamp assembly around the actuator.
(4) S 034-034Install a cap on the hydraulic hoses.
(5) S 024-007Remove each half of the walking beam (2) (AMM 32-11-15/401).
S 494-008
WARNING: MAKE SURE THE ATTACH POINT FOR THE HOIST IS CORRECTLY IN THE
_______ KEYHOLE SLOT. FAILURE TO DO THIS CAN CAUSE THE HOIST TO FALL AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(6)
Install the actuator sling.
S 864-035
(7)
Use the hoist to remove the load.
S 034-047
(8)
Do the steps that follow to remove the bolt (3) from the walking beam (2):
(a)
Remove the antirotation bolt (20) through the wide spacer (26) and the bolt (3).
(b)
Remove the antirotation bolt (20) through the narrow spacer (23) and the bolt (3).
(c)
Remove the lockwire between spacer nut (24) and narrow spacer (23).
(d)
Use the torque wrench adapter to loosen the spacer nut (24) on the threaded spacer (25).
(e)
Move the bolt (3) aft until the actuator head end is free.
NOTE: You can use the removal tool to move the bolt if it is
____ necessary. You must keep the parts in the same sequence that you removed them.
(f) Observe direction of Flanged Spacers (7), (9), (10).
S 024-010
(9)
Remove the actuator (1):
(a)
Remove the nut (35), the washer (36) and the lockbolt (39).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-32-01
ALL ú ú 01 Page 408 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b)
Remove the nut (37) and the washer (38).
(c)
Install the thread protector on the threads of the attach bolt (5).
(d)
Remove the attach bolt (5), the spacers (32), the washers (33), and the sleeve (34).
(e)
Use the actuator sling to remove the actuator (1) from the airplane.
(f)
Remove the tube assembly (4) and the clip (14) from the actuator (1).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(62)
