13. NYLON WASHER
12. NYLON
HYDRAULIC WASHER
HOSES
2. ACTUATOR SEE D (HEAD END)
BODY LANDING GEAR ACTUATOR HEAD END BOLT INSTALLATION
C
20. PACKING 24. PACKING
21. PACKING 25. PACKING
22. RING 26. RING
23. ADAPTER 27. ADAPTER
31. PACKING
30. PACKING
29. RING D
28. ADAPTER
Body Landing Gear Actuator Installation Figure 401 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-33-01
ALL ú ú 01 Page 406 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(2)
D00013 Grease - MIL-G-23827 (optional)
(3)
D00288 Lubricant - MCS 352 (Skydrol Assembly Lube)
(4)
D00196 Fluid-Hydraulic - BMS 3-11, Type IV, Class 1
(5)
C00174 Compound-Corrosion Preventive - MIL-C-16173, Grade 3
(6)
C00259 Enamel-Primer - BMS 10-11, Type I
D.
Parts ~.................................................... | AMM | | AIPC | ............. ...................... | FIG| ITEM | NOMENCLATURE | SUBJECT| FIG| ITEM | ...................................................... | 401| 1 | Washer |32-33-01| 01| 80 | | | 2 | Actuator Assembly | | | 160 | | | | (Actuator) | | | | | | 3 | Washer |32-13-02| 02| 55 | | | | (Tang Washer) | | | | | | 4 | Washer |32-33-01| 01| 85 | | | 5 | Nut |32-13-02| 02| 50 | | | 6 | Bolt (Lockbolt) |32-33-01| 01| 10 | | | 7 | Washer | | | 15 | | | 8 | Washer | | | 15 | | | 9 | Nut | | | 20 | | | 10 | Washer | | | 90 | | | 11 | Bolt | | | 25 | | | 12 | Washer | | | 35 | | | 13 | Washer | | | 35 | | | 14 | Washer | | | 30 | | | 15 | Nut | | | 40 | | | 16 | Nut | | | 20 | | | 17 | Washer | | | 15 | | | 18 | Washer | | | 15 | | | 19 | Bolt (Lockbolt) | | | 10 | | | 20 | Packing (O-ring) | | | 150 | | | 21 | Packing (O-ring) | | | 135 | | | 22 | Ring | | | 120 | | | 23 | Adapter | | | 105 | | | 24 | Packing (O-ring) | | | 155 | | | 25 | Packing (O-ring) | | | 140 | | | 26 | Ring | | | 125 | | | 27 | Adapter | | | 110 | | | 28 | Adapter | | | 100 | | | 29 | Ring | | | 115 | | | 30 | Packing (O-ring) | | | 130 | | | 31 | Packing (O-ring) | | | 145 | | | 32 | Bracket |32-53-11| 05| 205 | 2....…......…...................…........…....…......1
E.
References
(1)
AMM 09-11-00/201, Towing
(2)
AMM 12-21-01/301, Landing Gear
(3)
AMM 29-11-00/201, Hydraulic Supply System
(4)
AMM 32-00-30/201, Landing Gear Door Locks
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-33-01
ALL ú ú 01 Page 407 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
F. Access
(1)
Location Zone
755 Body Landing Gear, LH
765 Body Landing Gear, RH
G.
Procedure
S 434-010
(1)
If it is necessary to install the adapters (23, 27 and 28), do these steps (Fig. 401):
(a)
Lubricate the new packing (20, 21, 24, 25, 30, and 31), the backup rings (22, 26, and 29) and the adapters (23, 27, and 28) with hydraulic fluid or Skydrol Assembly Lube.
(b)
Install the packing (20, 21, 24, 25, 30, and 31), the backup rings (22, 26, and 29) and the adapters (23, 27, and 28) in the ports of the actuator.
S 424-011
(2) Connect the head end of the actuator (Fig. 401):
WARNING: YOU MUST USE THE SLING AND THE HOIST WHEN YOU MOVE THE
_______ ACTUATOR. THE ACTUATOR WEIGHS APPROXIMATELY 136 POUNDS AFTER YOU FILL IT WITH HYDRAULIC FLUID. IF THE ACTUATOR FALLS, IT CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(a) Use the sling and the hoist to put the actuator (2) in the correct position.
NOTE: The correct position for the actuator is between the
____ support structure and the shock strut. The adapters (23, 27 and 28) must be on the forward side of the actuator.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(124)
