(2)  
D00013 Grease - MIL-G-23827 (optional)

 (3)  
B00316 Solvent, TT-N-95, Type I

 (4)  
B00083 Solvent, TT-N-95, Type II

 C.
References

 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 29-11-00/201, Main Hydraulic Supply System

 (3)  
AMM 32-00-30/201, Landing Gear Door Locks

 (4)  
AMM 32-22-05/601, Nose Wheel Well Forward Door Bellcrank

 (5)  
AIPC 32-22-03 Fig. 2

 (6)  
AIPC 32-22-05 Fig. 1

 D.
Access

 (1)  
Location Zone
 711 Nose Landing Gear Door, Forward, LH
 712 Nose Landing Gear Door, Forward, RH

 E.
Procedure

 S 114-011
 (1)  
Use the solvent to clean the bolts, the washers, the nuts and the bearing surfaces.

 S 224-012

 (2)  
Examine for the worn parts and the fittings for the approved worn areas (AMM 32-22-05/601).

 S 424-013

 (3)  
Connect the bellcrank to the bellcrank support fitting
 (Section A-A, Fig. 401).

 (a)  
Put the bellcrank in the support fitting and install the spacer through the bulkhead fitting.

 NOTE: Use the left side of the wheel well through the
____ electronics compartment to get access to the bulkhead.
 (b)  
Install the bolt and the washer through the bellcrank support fitting and the bellcrank with the bolt head that points aft.

 (c)  
Install the washer and the nut to the bellcrank bolt.

 (d)  
Tighten the nut to 1100 - 1200 inch-pounds.

 S 434-014
 (4)  
Connect the door actuator rod to the clevis on the top of the bellcrank.

 (a)  
Install the washers between the actuator rod end and the clevis as shown in detail B.

 (b)  
Install the bolt with the bolt head against the ear of the clevis.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-22-05
 ALL  ú ú 01 Page 405 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 CAUTION:_______HOLD THE BOLT WHEN YOU TIGHTEN THE NUT. IT CAN PREVENT DAMAGE TO THE CLEVIS LOCKING DEVICE. LUBRICATE THE STRUCTURAL JOINTS DURING OR AFTER THE ASSEMBLY.
 (c)  Install the washer and tighten the nut to 200-300 pound-inches.
 S 434-015
 (5) Connect the left and the right door operator rod to the bellcrank.
 NOTE:____Do not change the left and right rods. You can install one of the two rods in the forward or aft clevis of the bellcrank.
 (a)  
Lubricate the bolt shank and the threads, and the bearing surface.

 (b)  
Install the bolt with the washers and the nut and tighten.

 F.
The procedure for the adjustment

 S 864-016
 (1)  Pressurize the hydraulic system No. 1 (AMM 29-11-00/201).
 S 494-017
 WARNING:_______REFER TO AMM 32-00-30/201 FOR LOCK INSTALLATION PROCEDURE. DO NOT MOVE THE DOORS TOO FAST, IT CAN CAUSE INJURY TO PERSONS. OR IF YOU DO NOT INSTALL THE LOCKS CORRECTLY, IT CAN CAUSE DAMAGE TO EQUIPMENT.
 (2)  
Make sure that all persons or equipment are clear of the doors for the main landing gear.

 (a)  
Or you install the door locks on the doors of the main landing gear (AMM 32-00-30/201).

 NOTE: The doors of the main landing gear will open and
____ close during the adjustment procedure.
 S 864-018
 WARNING:_______DO NOT MOVE THE DOORS TOO QUICKLY. IT CAN CAUSE INJURY TO PERSONS OR CAUSE DAMAGE TO EQUIPMENT. MAKE SURE ALL EQUIPMENT AND PERSONS ARE CLEAR OF THE DOOR AREA BEFORE YOU OPERATE THE DOORS.
 (3)  
Move the control handle of the landing gear to the DN position.

 S 824-034

 (4)  
Move the release handle to the close position to close the doors (See "Ground Door Release Handle Close Operation").

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(10)