EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-33-01
ALL ú ú 01 Page 408 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(c)
Put the bolt head in the antirotation retainer assembly.
(d)
Install the washer (14) and the nut (15).
(e)
Tighten the nut (15) to 50-60 pound-feet.
(f)
Loosen the nut to the nearest castellation.
(g)
Install the lockbolt (19), the washers (17, and 18), and the nut (15).
(h)
Remove the sling and the hoist.
(i)
Hold the actuator (2).
NOTE: Do this to make sure the rod end can move freely and
____
will not hit something.
(j)
Extend the rod end.
(k)
Fill the actuator (2) with BMS 3-11, hydraulic fluid.
(l)
Connect the hydraulic hoses to the actuator (2).
NOTE: All the hoses to the actuator ports must be the high
____ pressure type. You must install the hoses vertically (not crossed).
S 494-012
WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(3) Install the ground locks in all landing gear (AMM 09-11-00/201).
S 494-013
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(4) Do this task: "Body Landing Gear Door Lock Installation" (AMM 32-00-30/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-33-01
ALL ú ú 01 Page 409 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 494-023
(5)
Do this task: "Wing Landing Gear Door Lock Installation" (AMM 32-00-30/201).
S 494-024
(6)
Do this task: "Nose Landing Gear Door Lock Installation" (AMM 32-00-30/201).
S 864-033
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(7)
Pressurize hydraulic system No. 1 (AMM 29-11-00/201).
S 714-030
(8)
Do a check of the extension and retraction of the actuator:
(a)
Move the control handle for the landing gear to the DN position and the UP position five times.
NOTE:____ This will operate the actuator through five cycles. If
the actuator does not operate, it is possible the
door-operated sequence valve is not fully open.
(b) If the actuator does not operate when you move the control
handle, do these steps:
1) Make sure pressure is available to the actuator.
2) Push on the door and make sure you can see the rigging pin
hole for the door-operated sequence valve.
(c) Make sure the rod end of the actuator extends when you move the
control handle to the DN position.
NOTE:____ This shows that you connected the hydraulic hoses
correctly.
(d) Make sure there is no leakage at the actuator fittings.
S 864-016
(9)
Move the control handle to the OFF position.
S 094-027
(10)
Remove the sling and the hoist from the actuator.
S 494-028
(11)
Install the thread protector on the threads of the boss.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(125)
