(f)  
Make sure that the GEAR DISAGREE (CAUTION) indication comes into view on the top EICAS display.

 NOTE: The GEAR DISAGREE indication will not show for
____ approximately 25 to 35 seconds after you move the control lever. This occurs when you move the control lever from the DN to OFF or the DN to UP positions.
 (g)  Turn the EIU switch on the P2-4 panel between L, C, and R.
 1)  Make sure the GEAR DISAGREE (CAUTION) indication comes into view for the three EIUs.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-00
 ALL  ú ú 01 Page 503 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (h)  Move the control lever to the UP position.
 1)  Make sure that the GEAR DISAGREE (CAUTION) indication comes
 into view on the top EICAS display.
 (i)  Make sure that the GEAR DOOR (ADVISORY) indication comes into
 view on the top EICAS display when the doors are open.
 NOTE:____ The GEAR DOOR indication will not come into view for
 approximately 25 to 35 seconds after the doors open.
 (j)  Make sure that the top EICAS display shows a symbol for each of
 the five landing gear.
 NOTE:____ If the landing gear moves while in the locked down
 position, an in-transit condition can show.  This can
 occur as an alternative to the DN condition.
 (k)  Make sure the lower EICAS display shows that all five landing
 gear doors are open (five slashed boxes).
 (l)  Turn the EIU switch on the P2-4 panel between L, C, and R.
 1)  Make sure the GEAR DOOR display shows for the three EIUs.
 2)  Make sure the lower EICAS display for all landing gear
 shows for the three EIUs.

 S 495-054
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR HANDLE LOCKS ON THE GROUND RELEASE HANDLES FOR THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR HANDLE LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (6)  Do this task: "Installation of the Handle Locks on the Ground Release Handles for the Main Landing Gear" (AMM 32-00-30/201).
 S 865-055
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (7)  
Make sure the door actuators for the doors for the wing landing gear hold the doors open.

 S 485-064

 (8)  
Install the rigging pins (WD-1 LH, WD-2 RH) in the left side and the right side door-operated sequence valves.

 (9)  
Make sure the rigging pins do not rub when you install them.

 S 715-065
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-00
 ALL  ú ú 01 Page 504 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 865-066
 (10)
 Move the control lever to the OFF position.

 S 485-067

 (11)
 Install the rigging pins (WD-5 and WD-6) in the left side and the right side downlock-operated sequence valves.

 S 715-068

 (12)
 Make sure the rigging pins do not rub when you install them.

 S 085-044

 (13)
 Remove the rigging pins from the door-operated sequence valves.

 S 085-045

 (14)
 Remove the rigging pins from the downlock-operated sequence valves.

 S 095-014
 WARNING:_______ YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
 DOOR HANDLE LOCKS FROM THE GROUND RELEASE HANDLES FOR THE THE
 LANDING GEAR DOORS.  THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT
 REMOVE THE DOOR HANDLE LOCKS CORRECTLY.  THIS CAN CAUSE INJURY

 TO PERSONS AND DAMAGE TO EQUIPMENT.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(52)