72-54-00
 ALL  ú ú C01 Page 607 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
3)  There is a minimum distance of 1.0 inch (25.4 mm) between other nicks, scores and scratches.
 F.  LPT Threaded Ports and Bosses Inspection
 S 216-022-C00
 (1)  Examine the threads of the ports and bosses for damaged threads
 (Fig. 601):

 (a)  It is permitted to have one complete turn of the thread gone. This thread can be continuous damage or cumulative for the full boss or port thread. To find the total cumulative damage, you must follow the full thread length.
 S 216-023-C00
 (2)  Examine the ports and bosses for cracks in the welds (Fig. 601):
 (a)  
One crack for each port or boss is permitted if it is not more than 0.04 inch (1.00 mm) in length.

 (b)  
A maximum service extension of 50 cycles is permitted for one crack that is 0.5 inch (12.7 mm) in length if there is no air leakage.

 G.  2nd- and 3rd-Stage LPT Borescope Plugs Inspection
 NOTE: This inspection examines the 2nd- and 3rd-stage borescope
____ plugs to see if the 2nd- or 3rd-stage LPT vane segments have turned circumferentially. The 2nd- or 3rd-stage LPT vane segments turn circumferentially when the anti-rotation lock no longer holds the vane segments in position. When the vane segments turn, they damage the EGT thermocouples and the borescope plugs. This inspection examines the borescope plugs to see if the vane segments have turned.
 S 026-036-C00
 CAUTION: WHEN YOU DO AN INSPECTION OF THE 2ND- AND 3RD-STAGE BORESCOPE
_______ PLUGS, DO NOT REMOVE AND EXAMINE THE TWO PLUGS AT THE SAME TIME. FIRST REMOVE AND EXAMINE THE 2ND-STAGE PLUG, THEN INSTALL IT AND DO THE STEPS AGAIN FOR THE 3RD-STAGE PLUG. IF YOU REMOVE THE TWO PLUGS AT THE SAME TIME, YOU CAN ACCIDENTALLY INTERMIX THEM. THIS CAN CAUSE DAMAGE TO THE ENGINE.
 (1)  Remove the 2nd-stage borescope plug as follows (Fig. 602):
 (a)  Remove the rigid borescope plug from the turbine case at the 3 o'clock position.
 S 216-037-C00
 (2)  Examine the 2nd-stage borescope plug as follows (Fig. 603):
 (a)  If you can remove the borescope plug, make an inspection as follows: 1) Small marks in areas A, B and C, shiny or not, where two
 surfaces touch are permitted. 2) Worn surfaces or missing material in area B is permitted.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-54-00
 ALL  ú ú C02 Page 608 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////

A-A

2nd- and 3rd-Stage Rigid Borescope Plug Location Figure 602
C73877
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-54-00
 ALL  ú ú C01 Page 609 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////

THERMAL SHIELD CAN TOUCH THIS AREA. THIS CONDITION IS SERVICABLE.

LIGHT CONTACT MARKS (SHINY OR NOT)
SERVICEABLE

2nd- and 3rd-Stage Rigid Borescope Plug Visual Inspection
Figure 603 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-54-00
 ALL  ú ú C01 Page 610 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
C73887
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
AREA A
AREA B
AREA C
NON-SERVICEABLE
AREA A
AREA B
AREA C
SERVICEABLE EXAMPLE OF RIGID BORESCOPE PLUG CONDITION 2nd- and 3rd-Stage Rigid Borescope Plug Visual InspectionFigure 603 (Sheet 2)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 ENGINE 發動機 2(82)