72-33-00
ALL ú ú C01 Page 836 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
FAN FRAME STRUT
RTV S-M56-MM-00539-00-B
Inner and Outer Radial Drive Shaft Housing
Figure 808 (Sheet 2)
C85994
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-33-00
ALL ú ú C01 Page 837 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S-M56-MM-00538-00-B
Inner and Outer Radial Drive Shaft Housing Figure 808 (Sheet 3)
C85998
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-33-00
ALL ú ú C02 Page 838 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
C
INNER HOUSING O-RING
AREA FOR PRIMER, RTV
C-C
S-M56-MM-00541-00-B
Inner and Outer Radial Drive Shaft Housing Figure 808 (Sheet 4)
C85999
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-33-00
ALL ú ú C02 Page 839 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(i) Apply a layer of 1200 primer with a brush at these areas:
NOTE: Let the primer dry for 1 hour before you apply the RTV.
____
1) The rabbet diameter and along the large diameter of the inner housing for 1.77 inches (45.00 mm). 2) The bore diameter of the No. 10 strut.
(j)
Apply a layer of RTV 730 on the outer rabbet diameter and along the large diameter of the inner housing for 1.77 inches
(45.0 mm).
(k)
Install the inner and outer housings in the fan frame.
(l)
Remove the guide puller.
(m)
Install the four bolts that attach the outer housing.
1) Tighten the bolts to 145-160 pound-inches
(16-18 newton meters).
(n)
Let the RTV dry for 5 hours before you install the RDS and
transfer gearbox.
S 418-049-C00
(7) Do these steps to install the RDS:
(a) Remove the radial drive shaft from the protective tube.
CAUTION: BE CAREFUL WHEN YOU ENGAGE THE SPLINES ON THE RADIAL DRIVE
_______
SHAFT INTO THE INLET GEARBOX. IF YOU DO NOT OBEY THIS
PRECAUTION, DAMAGE TO THE SEALS CAN OCCUR.
(b)
Put a light layer of engine oil on the splines at the two ends.
(c)
Carefully move the collar end (outward) on the RDS through the RDS port.
(d)
Make sure the splines are fully engaged.
NOTE: Splines are fully engaged when the RDS points out
____ 0.640 + 0.040 inch (16.25 + 1.00 mm) from the RDS port.
S 418-050-C00
(8) Install the transfer gearbox (AMM 72-62-01/401).
S 418-051-C00
WARNING: OBEY THE INSTRUCTIONS IN THIS PROCEDURE WHEN YOU CLOSE THE
_______ THRUST REVERSER. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
(9)
Close the left and right thrust reverser (AMM 78-31-00/201).
(10)
Close the left and right fan cowl panels (AMM 71-11-02/201).
S 418-052-C00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 ENGINE 發動機 2(43)
