S-M56-MM-1040-(1)-02-B
Magnetic or Sealol Seal Removal With the Puller Figure 202
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-60-00
ALL ú ú C05 Page 205 ú Mar 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
2) Tighten the nut until the rotating ring is held tight by
the claws.
3) Tighten the screw.
4) Use the slide hammer to remove the rotating ring.
5) Remove and discard the O-ring.
6) Loosen the nut and the screw.
7) Remove the rotating ring from the tool.
TASK 72-60-00-402-005-C00
3. Magnetic Seal Installation (Fig. 201)
__________________________
A. Consumable Materials
(1)
D00000 Grease - Graphite, Aeroshell Compound 08
(2)
Oil - Engine
(3)
B00062 Solvent - Acetone, O-A-51
B. References
(1)
ENGINES WITH A CONSTANT SPEED DRIVE/AC GENERATOR;
AMM 24-11-11/401, Generator Constant Speed Drive
(2)
ENGINES WITH A VSCF GENERATOR/CONVERTER;
AMM 24-11-11/401, VSCF Generator/Converter
(3)
AMM 29-15-11/401 and/or AMM 29-15-12/401, Hydraulic Systems A and B Engine Driven Pump (EDP)
(4)
AMM 71-71-00/601, Engine Vents and Drains
(5)
AMM 72-63-00/501, Accessory Gearbox
(6)
AMM 73-11-01/401, Fuel Pump Package
(7)
AMM 80-11-01/401, Engine Starter
C. Access
(1)
Location Zones
502 Engine No. 1 - Accessory Gearbox
602 Engine No. 2 - Accessory Gearbox
(2)
Access Panels
5746L Engine No. 1 - Left Fan Cowl Panel
5846R Engine No. 2 - Left Fan Cowl Panel
D. Procedure
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-60-00
ALL ú ú C09 Page 206 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 112-007-C00
WARNING:_______ DO NOT GET THE SOLVENT IN YOUR MOUTH OR EYES, OR ON YOUR SKIN.
DO NOT BREATHE THE FUMES FROM THE SOLVENT. PUT ON A PROTECTIVE
SPLASH GOGGLE AND GLOVES WHEN YOU USE THE SOLVENT. KEEP THE
SOLVENT AWAY FROM SPARKS, FLAME, AND HEAT. THE SOLVENT IS
POISONOUS AND FLAMMABLE. IT CAN CAUSE INJURY TO PERSONS AND
DAMAGE TO EQUIPMENT.
(1) Clean the gear area, that will touch the rotating ring, with the solvent:
(a) Remove all of the oil solids that stay on the gear area.
NOTE: This will prevent possible damage to the O-ring when you
____ install it.
S 212-008-C00
(2) Examine the O-rings for the seal housing (OD), static seal case (OD), and rotating ring (ID):
(a) If there are cuts, nicks, or other damage, replace the O-rings.
S 422-009-C00
CAUTION: USE CLEAN, LINT-FREE GLOVES WHEN YOU TOUCH THE MAGNETIC SEALS.
_______ THIS WILL PREVENT CONTAMINATION.
CAUTION:_______MAGNETIC SEALS ARE ALIGNED ASSEMBLIES. IF YOU CAUSE DAMAGE TO A COMPONENT OF THE SEAL, YOU MUST REPLACE ALL OF THE SEAL.
(3) Install the magnetic seal:
(a)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 ENGINE 發動機 2(113)
