曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

_______ FRAME WHEN YOU REMOVE THE STUDS. IF YOU CUT INTO THE METAL YOU CAN CAUSE DAMAGE TO THE EQUIPMENT.
 (2)  Remove the studs (Fig. 805A):
 NOTE:____Use one of these two options to remove the studs. Option one is for studs that have locking tabs, and option two is for studs without locking tabs.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-56-00
 ALL  ú ú C01 Page 817 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
A
LPT FRAME
A
STUDS
FWD
A
//////////////////////// / /
CFM56 ENGINES
/ / ////////////////////////
LPT FRAME
STUD
FWD
A-A
S-M56-MM-03508-000-B
Studs on the LPT Frame Strut
Figure 805A

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-56-00
 ALL  ú ú C01 Page 818 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F61803
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////

S-M56-SM-07533-00-C
Measurement of Spotfacing Radius
Figure 805B

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-56-00
F71141
ALL  ú ú C01 Page 819 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
CHAMBER 0.047-0.055 AT 45`

FRAME
SIDE

S-M56-SM-07534-00-C
Reworking of Stud Figure 805C
 F71155
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-56-00
 ALL  ú ú C01 Page 820 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(a)  OPTION ONE: Remove the studs that have locking tabs. 1) Use a thin grinding wheel to remove the tack weld. 2) Loosen and remove the stud.
 a)  Discard the stud.
 3)  Disengage the locking tab from its groove.
 4)  Look for the weld material in the insertion groove for the
 locking tab. 5) Remove the weld material that you find with the grinding wheel.
 (b)  
OPTION TWO: Remove the studs that do not have locking tabs. 1) Use a thin grinding wheel to remove the tack weld. 2) Loosen and remove the stud.

 a)  Discard the stud.

 (c)  
Use clean, dry, compressed air to remove unwanted material from the repair area.

 S 428-034-C00
 (3)  Install a new stud (Fig. 805A):
 NOTE: The locking tab has been deleted and is no longer needed .
____ Use this procedure whatever the previous configuration.
 (a)  Install the studs that do not have locking tabs.
 1)  Measure the radius that is found in the stud hole in the frame (Fig. 805B).
 NOTE: The CFMI Turbine Rear Frame has two possible
____
 configurations:

 -
Configuration One has stud holes with a radius of 0.008-0.016 inch (0.2-0.4 mm).

 -
Configuration Two has stud holes with a radius of 0.039-0.047 inch (1.0-1.2 mm).

 a)  If the stud hole radius measures between 0.008 inch
 (0.2mm) and 0.016 inch (0.4 mm) (Configuration One),
 continue the procedure.
 b)  If the stud hole radius measures more than 0.016 inch
 (0.4 mm) (Configuration Two), rework the stud per CFMI SPM 70-44-10 (Fig. 805C). 2) Apply a thin layer of graphite grease to the threads and
 mating surfaces of the new stud. 3) Use your hand to install the stud. 4) Tighten the stud to a torque of 490 to 530 pound-inches
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 ENGINE 發動機 2(106)