(a)  
Attach the cables to the follow-up drum on the aft side of the flap power unit: 1) Make sure the cable routing is correct. 2) Wind the WFFA cable approximately 2-1/4 times around the

 follow-up drum on the flap power unit. 3) Wind the WFFB cable approximately 1/3 times around the follow-up drum on the flap power unit. 4) Make sure cable WFFA is around the follow-up drum on the flap control unit approximately 1-1/2 turns. 5) Make sure cable WFFB is around the follow-up drum on the flap control unit approximately 2-1/2 turns.

 (b)  
Adjust the tension in the cables to the correct tension shown in the table:

 ~.............................................. | TEMPERATURE | CABLE ADJUST LOAD | | (°F) | (+10/-0 POUNDS) *[1] | ................................................
 |  110  |  71  |
 |  90  |  65  |
 |  70  |  60  |
 |  50  |  55  |
 |  30  |  49  |
 |  10  |  44  |
 |  -10  |  38  |
 |  -30  |  33  |
 |  -40  |  30  |

 2...................…..........................1
 *[1] For a periodic check when there is no discrepancy report, the tension in the cables can be +/-20 pounds from the tension in the table. If you will measure the tension because of a discrepancy report, the tension in the cables can be +/-15 pounds from the tension in the table. When you adjust the tension in the cables, you must use the values from the table.
 NOTE: Permit the temperature of the airframe to stay the same
____ (| 5°F) for a minimum of 1 hour before you measure the tension.
 (c)  
Make sure you can easily install the rig pin in the flap control unit.

 (d)  
Install the locking clips on the turnbuckles.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-54
 ALL  ú ú 02 Page 407 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 984-024
 CAUTION: MAKE SURE THE ANGULAR CLEARANCE IS 1/4 TO 5/6 TURNS IF YOU HAVE
_______ MADE LATERAL TRIM CORRECTIONS. A DIMENSION X NOT IN THIS LIMIT CAN CAUSE DAMAGE TO THE FLAP.
 (7)  
Turn the torque tubes until the ballscrew nut upstop is 170 to 190 degrees (1/2 turn |10 degrees) from the upstop (Fig. 403).

 S 434-025

 (8)  
Attach the torque tubes to the flap power unit (Fig. 401):

 (a)  
Apply a thin layer of the grease to the torque tube sleeves and the couplings on the flap power unit.

 (b)  
Put the torque tubes on the flap power unit.

 (c)  
Install the retaining screws to attach the torque tubes to the couplings.

 (d)  
Install the lockwire on the retaining screws.

 S 084-026
 (9)  
Remove the rig pin F-1 from the flap control unit.

 S 864-029

 (10)
 Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6 Panel
 1) ALT TE FLAP DRIVE AC

 (11)
 Do the test of the flap power unit (Ref 27-51-54/501).

 (12)
 Fill the hydraulic reservoir if it is necessary (Ref 12-12-00/301).

 (13)
 Install the inboard flap track fairings (Ref 27-51-32/401).

 S 724-030
 S 614-031
 S 414-032
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-54
 ALL  ú ú 02 Page 408 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE  A 
ASSEMBLY FLAP TRANSMISSION  DOWNSTOP  DOWNSTOP 
FWD  SEE B UPSTOP  A BALLSCREW NUT  (BALLSCREW NUT) UPSTOP UPST0P (SCREW YOLK) BALLSCREW (EXAMPLE) 
DIMENSION "X" 
Flap Transmission Upstop Clearance Figure 403  B 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(92)