EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-11
 ALL  ú ú 01 Page 401 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

MIDFLAP

A-A

Inboard Aftflap Installation

Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-11
 ALL  ú ú 01 Page 402 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
AFTFLAP
PUSHROD

B-B

TOP FLIGHT ROLLER
TOP DEAD-WEIGHT ROLLER

Inboard Aftflap Installation
Figure 401 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-11
 ALL  ú ú 01 Page 403 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 414-021
 CAUTION:_______DO NOT RETRACT THE FLAPS. THE PUSHRODS CAN CAUSE DAMAGE TO THE REAR SPAR OF THE MIDFLAP.
 (6)  If you will not install the aftflap immediately, install the trailing edge of the midflap.
 NOTE: It is not necessary to install or tighten all of the screws
____
 on the trailing edge.

 TASK 27-51-11-404-008
 3. Aftflap Installation
____________________
 A. References
 (1)  
27-51-00/201, Trailing Edge Flap Systems

 (2)  
27-51-11/601, Inboard Aftflap

 B.
Access

 (1)  
Location Zone 309, 409 Wing Trailing Edge Flap and Spoilers

 C.
Procedure

 S 224-009
 (1)  
If you will install used parts, do this task: "Aftflap Inspection" (Ref 27-51-11/601).

 S 014-010

 (2)  
If it is necessary, remove the trailing edge of the midflap (Fig. 401).

 S 424-011

 (3)  
Install the aftflap:

 (a)  
Loosen each deadweight roller eccentric and disengage it from its locking plate.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-11
 ALL  ú ú 02 Page 404 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  
Adjust each deadweight roller cam to get the maximum clearance from the flap track.

 (c)  
If it is necessary, remove the bottom flight rollers from each carriage.

 (d)  
Put the aftflap on the tracks in the midflap.

 (e)  
Install the bottom flight rollers. 1) Put the two rollers on the carriage. 2) Install the bolt in the rollers. 3) Attach the rollers with the two washers, nuts and cotter

 pins.
 S 824-012
 (4)  Adjust the eccentric bushings on the dead-weight rollers at the inboard and outboard aft flap tracks first:
 NOTE:____There are four aftflap carriages. Each side of each carriage includes one top dead-weight roller, one top flight roller, one bottom dead-weight roller, and one bottom flight roller.
 (a)  
With the aftflap fully extended, and with the deadweight rollers in contact with the flap tracks, make sure that the deadweight rollers do not contact the stops.

 (b)  
Adjust the forward deadweight rollers to get the minimum clearance between the forward flight rollers and the flap tracks (0.002 - 0.005 inch).

 (c)  
Adjust the aft deadweight rollers to get a clearance between the aft flight rollers and the flap tracks that is equal to or larger than the clearance on the forward flight rollers, but not more than 0.020 inch.

 (d)  
Adjust the deadweight rollers on the center aft flap tracks the same way as the inboard and outboard aft flap track deadweight rollers.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(11)