shaft. 2) Remove the quadrant segment from the airplane. 3) Move the shaft down and remove it from the airplane.
(b)
Remove the eight screws and three bolts to disconnect the quadrant support.
(c)
Remove the quadrant support from the airplane.
TASK 27-51-77-404-009
3. Flap Control Quadrant Installation
__________________________________
A. Consumable Materials
(1)
A00136 Sealant - BMS 5-19, Class A
(2)
D00015 Grease - BMS 3-24
B.
References
(1)
25-27-15/401, Carpets
(2)
25-52-65/401, Cargo Compartment Ceiling Lining
(3)
27-51-74/401, Flap Control Unit
(4)
53-21-00/401, Passenger Cabin Floor
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-77
ALL ú ú 01 Page 403 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
A
A
CONTROL
STAND
CONTROL STAND
A A
FWD
FWD
AIRPLANES WITH EFIS
AIRPLANES WITHOUT EFIS
FLAP CONTROL
LEVER
ADJUSTMENT LOAD
0.187 |0.005 INCH
+10/-0 POUNDS 3/32 AND 1/8 INCH
FLAP DETENT
TEMP
DIAMETER CABLESPLATE LEVER WFA AND WFB 2
`F 1LATCH
3 4
110117
152 90
108
140 70
100
130 50
91
118 30
83
108+10
74
96-10
65
85-30
57
74-40
52 68
FWD
A-A
3 AIRPLANES WITH TWO-PIECE WFA/WFB FLAP CONTROL
1 TO MAKE SURE YOU GET THE 2 THE FORWARD CABLES ARE CABLE
CORRECT CABLE TENSION, 3/32 INCH DIAMETER. THE PERMIT THE AIRFRAME AFT CABLES ARE 1/8 INCH 4 AIRPLANES WITH ONE-PIECE TEMPERATURE TO STABILIZEDIAMETER. WFA/WFB-2 FLAP CONTROL (|5` F) FOR A MINIMUM OF CABLE ONE HOUR.
Flap Control Lever Rigging Position Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-77
ALL ú ú 02 Page 404 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
C. Access
(1)
Location Zone
202 Lower Nose Compartment
218 Aft Cargo Compartment
(2)
Access Panels
1103L Forward Access Door
D.
Procedure
S 164-010
(1)
Remove the sealant from the wheel well ceiling in the area of the flap control quadrant.
S 394-011
(2)
Apply a layer of the sealant in and around the top surface of the 15 holes in the wheel well ceiling.
S 034-012
(3)
If the access is through the aft cargo compartment, remove the quadrant segment (Fig. 401):
(a)
Remove the bolt that attaches the quadrant segment to the shaft.
(b)
Remove the shaft from the quadrant support.
S 424-013
(4)
Install the flap control quadrant:
(a)
Put the quadrant support on the wet sealant with the studs through the wheel well ceiling.
NOTE: Make sure the quadrant stops are inboard of the shaft.
____
(b)
Install the three bolts to attach the quadrant support.
NOTE:____Make sure the head of the inboard bolt is up. Make sure the heads of the outboard bolts are down.
(c)
Install the washer and nut on each bolt.
(d)
Install the eight screws with their heads down.
(e)
Install the washers and nuts on the screws.
S 434-014
(5)
If the access is through the aft cargo compartment, install the quadrant segment and the shaft:
(a)
Move the shaft up through the quadrant support until the shaft touches the bearings.
(b)
Put the quadrant above the stop and engage the splines.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(136)
