曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 measure if the indicator is clamped to other nearby
 structures.
 (b) Pull the bearing aft (10-30 pounds) by hand. Set the indicator
 to zero.
 (c) Push the bearing forward (10-30 pounds) by hand. Measure and
 record the total radial movement.
 (d) If the total radial movement is more than 0.007 inches, then
 replace the bearing.
 S 866-011
 (8)  Make sure the speed brake lever is in the UP position.
 S 086-018
 (9)  Remove the spoiler actuator locking tools.
 S 446-017

 (10)
 Do this task:  "Trailing Edge Flap System Activation" (AMM 27-51-00/201).

 S 866-012

 (11)
 Do this task:  "Pressurize the A, B, or Standby Hydraulic System" (AMM 29-15-00/201).

 S 866-013

 (12)
 Put the speed brake lever in the DOWN position to lower the spoilers.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-47
 ALL  ú ú 01 Page 605 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 866-021
 WARNING:_______ MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE TRAILING
 EDGE FLAPS, THE LEADING EDGE FLAPS AND SLATS AND THE DRIVE
 MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER.  THIS CAN
 CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.

 (13)
 Move the flap control lever to the 0-unit (flaps up) detent to retract the flaps.

 S 866-015

 (14)
 Do this task:  "Remove Power from the A, B, or Standby Hydraulic System" (AMM 29-15-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-47
 ALL  ú ú 01 Page 606 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
A
TOGGLE
DIAL
INDICATOR
SETUP
(EXAMPLE)

A
SEQUENCE
CARRIAGE
FWD INBD
TOGGLE
PUSH PULL
A-A

Outboard Foreflap Toggle Bearing Inspection
Figure 602

G96977
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH NON-LUBRICATED BEARINGS ú

 27-51-47
 ú ú 01 Page 607 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 OUTBOARD FLAP TRACKS - REMOVAL/INSTALLATION
___________________________________________
 1.  General
_______
 A.  There are two tasks in this procedure. There is a task for the removal and a task for the installation of the outboard flap tracks.
 (1)  It is very important to keep the initial thickness of the shims. The installation procedure has instructions for the replacement of damaged or lost shims. If you do not follow the instructions, the flap track can be not aligned.
 TASK 27-51-49-004-001
 2.  Outboard Flap Track Removal
___________________________
 A.  Special Tools and Equipment
 (1)  Inboard Flap Rigging Beam - F80209-2
 NOTE: The Rigging Beam is a part of F80209-1.
____
 B.  References
 (1)  
AMM 27-51-34/401, Outboard Trailing Edge Flap

 (2)  
AMM 27-51-47/401, Outboard Flap Sequence Carriage

 (3)  
AMM 27-51-71/401, Flap Transmission

 C.  
Access

 (1)  
Location Zone 307, 407 Wing Trailing Edge Outboard Flap and Spoilers

 D.  
Procedure

 S 824-016
 (1)  
If you will install the same flap and a new or overhauled flap track, measure the flap alignment with the wing chord plane (WCP).

 (a)  
Make sure the flaps are in the fully retracted position.

 (b)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(77)