曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

BOLT  OD  0.2495  0.2495  0.2480  X 
21  BEARING  ID  0.2495  0.2500  0.2515  0.0020  X 
BOLT  OD  0.2490  0.2495  0.2475 X 
22  BEARING  ID  0.2500  0.2515  0.2545  0.0050  X 
BOLT  OD  0.2490  0.2495  0.2450  X 
23  BUSHING  ID  0.3750  0.3756  0.3777  0.0032  X 
BUSHING  OD  0.3740  0.3745  0.3718 X 
24  BUSHING ID  0.2500  0.2515  0.2545  0.0050  X 
BOLT  OD  0.2490  0.2495  0.2450 X 
25  BUSHING  ID  0.2500  0.2505  0.2525  0.0030 X 
BOLT  OD  0.2490  0.2495  0.2470  X 
26  BUSHING  ID  0.3750  0.3756  0.3777  0.0032 X 
BUSHING  OD  0.3740  0.3745  0.3718  X 
27  BUSHING  ID  0.2500  0.2515  0.2545  0.0050 X 
BOLT  OD  0.2490  0.2495  0.2450  X 
28  BEARING  ID  0.2495  0.2500  0.2515  0.0020 X 
BOLT  OD  0.2490  0.2495  0.2475 X 

Exhaust Gate Actuation Mechanism Wear Limits Figure 602 (Sheet 5)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH THREE EXHAUST GATE ú

 27-51-34
 PUSHRODS.  ú CONFIG 1 ú 01 Page 607 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A12097
A 737-300/400/500MAINTENANCE MANUAL
 S 226-006-001
 (5)  
Measure the movement of the midflap carriage:

 (a)  
Manually move the carriage forward and aft.

 (b)  
Measure the axial movement of the carriage.

 NOTE: Make sure the midflap does not move during the
____
 measurement.

 S 226-007-001
 (6)  
If the axial movement is more than 0.005 inch, do this task to replace the carriage bearing: "Outboard Midflap Carriage Removal" (Ref 27-51-44/401).

 S 416-008-001

 (7)  
Install the access panel:

 (a)  
Apply a layer of the sealant between the surfaces of the access panel and the midflap.

 (b)  
Install the access panel with the fasteners.

 S 866-009-001
 (8)  
Do this task to pressurize hydraulic system B: "Supply Hydraulic Power" (Ref 27-51-00/201).

 S 866-015-001

 (9)
Put the flap control lever in the UP detent to retract the flaps.

 S 866-010-001

 (10)
 Do this task to depressurize hydraulic system B:  "Remove Hydraulic Power" (Ref 27-51-00/201).

 TASK 27-51-34-226-011-001
 3. Outboard Trailing Edge Flap Exhaust Gate Actuation Mechanism Inspection
_______________________________________________________________________
 A. Standard Tools and Equipment
 (1)  
Micrometer 0 to 1 inch

 B.
References

 (1)  
27-51-34/401, Outboard Trailing Edge Flap

 C.
Access

 (1)  
Access Panels
 8215, 8715 Exhaust Gate Linkage Access Panel

 D.
Procedure

 S 016-012-001
 (1)  Do this task: "Outboard Trailing Edge Flap Removal" (Ref 27-51-34/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH THREE EXHAUST GATE ú

 27-51-34
 PUSHRODS.  ú CONFIG 1 ú 02 Page 608 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 226-013-001
 (2)  
Measure the parts on the actuator mechanism for the exhaust gate (Fig. 602):

 (a)  
Remove the parts.

 (b)  
Use a micrometer to measure the parts.

 (c)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 602.

 (d)  
Replace the parts that are not in the tolerance.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(50)