(c)  
Remove the carriage bearing support: 1) Remove the four bolts on the carriage bearing support to

 the midflap. 2) Remove the shims from the carriage bearing support. 3) Measure and make a record of the thickness of the shims at
 the carriage bearing supports.
 (d)  Remove the spindle bearing from the aft end of the carriage:
 1)  Remove the nut and washers from the aft end of the carriage.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-44
 ALL  ú ú 01 Page 401 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
SEE A
ACCESS PANEL 
BEARING SUPPORT 
BOLT 
(4 LOCATIONS) 
A 
BOLT 
BUSHING 
SAFETY LINK 
BOLT 
SPACER 
RADIUS FILLER 
NUT 
COTTER PIN 
SIDE ROLLERS 
A 
OUTBOARD MIDFLAP CARRIAGE 
A 

Outboard Midflap Carriage Installation
Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-44
 ALL  ú ú 01 Page 402 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500MAINTENANCE MANUAL
CARRIAGE BEARING SUPPORT SEE C
SHIM
SEE B
MIDFLAP
FLAP
CARRIAGE

TAPERED
FILLER RETAINER SHIMS
LEAF SPRINGS
A-A
SEE D
SPECIAL BOLT
BORE OF CARRIAGE
SUPPORT FITTING
 BMS 3-27
WASHER
NUT
BEARING CARRIAGE
RETAINER BOLT (4 LOCATIONS)
CARRIAGE SUPPORT
CARRIAGE BEARING FITTING
SUPPORT  2 B
1.20
INCHES SHIM
1.10
0.25
APPLY PRIMER INCH 1
0.15
AND TEFLON
FILLED COATING 0.10
 INCH 1
0.07
MIDFLAP
TAPERED SHIMSFILLER
C D
APPLY THE BMS 5-95 SEALANT
1
BOLT ORIENTATION OPTIONAL
2
Outboard Midflap Carriage Installation
Figure 401 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-44
 ALL  ú ú 01 Page 403 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 2)  Remove the bearing and the bearing inner race from the carriage.
 (e)  Move the carriage out of the flap.
 S 034-005
 (4)  
Remove the spherical bearing if it is necessary:

 (a)  
Remove the bearing retainer from the midflap.

 (b)  
Remove the spherical bearing.

 (c)  
Remove the seal if it is loose or damaged.

 TASK 27-51-44-404-006
 3.  Outboard Midflap Carriage Installation (Fig. 401)______________________________________
 A.  Consumable Materials
 (1)  
A00247 BMS 5-95 Sealant

 (2)  
C00304 BMS 10-86, Type II Teflon Filled Coating

 (3)  
C00308 MIL-C-11796 Corrosion Preventive Compound

 (4)  
C00325 BMS 10-11 Primer

 (5)  
D00014 MIL-G-21164 Grease

 (6)  
G01395 BMS 3-27 (MASTINOX 6856K) CORROSION PREVENTIVE COMPOUND

 B.  
References

 (1)  
27-51-34/401, Outboard Trailing Edge Flap

 (2)  
27-51-44/601, Outboard Midflap Carriage

 C.  
Access

 (1)  
Location Zone 307, 407 Wing Trailing Edge Outboard Flap and Spoilers

 (2)  
Access Panels
 8207, 8707 Outboard TE Flap Access Panel
 8208, 8708 Outboard TE Flap Access Panel

 D.  
Procedure

 S 224-007
 (1)  
If you will install used parts, do this task: "Outboard Midflap Carriage Inspection" (Ref 27-51-44/601).
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 4(68)