5. BUSHING/BOLT
C-C
Inboard Aft Flap Wear Limits Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-11
ALL ú ú 01 Page 602 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
ALL DIMENSIONS ARE IN INCHES
Inboard Aft Flap Wear Limits
Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-11
ALL ú ú 01 Page 603 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H54882
A
737-300/400/500MAINTENANCE MANUAL
INBOARD MIDFLAP CARRIAGE - REMOVAL/INSTALLATION
_______________________________________________
1. General
_______
A. There are two tasks in this procedure. There is a task for the removal and a task for the installation of the inboard midflap carriage. It is necessary to remove the applicable flap and the flap track fairing from the airplane before you remove the carriage.
TASK 27-51-14-004-001
2. Inboard Midflap Carriage Removal (Fig. 401)
________________________________
A. Special Tools and Equipment
(1) Rig Pins (F-5 and F-6) - 0.248 +0.000/-0.002 inch diameter, 3.7 +/-0.25 inches long (MS20392-3)
NOTE: The rig pins are part of the kit F0207-69, -78, or -83
____
B. References
(1)
27-51-04/401, Inboard Trailing Edge Flap
C.
Access
(1)
Location Zone 309, 409 Wing Trailing Edge Inboard Flap and Spoilers
D.
Procedure
S 014-002
(1)
Do this task: "Inboard Trailing Edge Flap Removal" (Ref 27-51-04/401).
S 034-003
(2)
On an inboard carriage, disconnect the boom cables:
(a)
Install a clamp on the boom cables where the cables go through the midflap end rib.
(b)
Remove the rig pins from the boom.
NOTE: You install the rig pins during the trailing edge flap
____
removal.
(c)
Loosen the cables at the two ends of the boom.
(d)
Install the rig pins on the two sides of the boom roller.
(e)
Remove the pulley bracket (11).
NOTE: Do not remove the cable guards or the cables from the
____ pulley and bracket assembly.
1) Let the bracket assembly hang from the torque shaft (4).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-14
ALL ú ú 01 Page 401 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
SEE A
SEE B
1. BOOM
A
SEE C
2. CARRIAGE RETAINING BOLTS BOLTHEAD OUT (THIS BOLT ONLY) SEED
11. PULLEY
BRACKET
4. TORQUE
10. PLATE SHAFT
SIDE ROLLER (2 LOCATIONS EACH INBOARD AND OUTBOARD CARRIAGE)
9. CAM
5.
CARRIAGE HALF
6.
PULLEY AND BOOM ROLLER SUPPORT
8. CARRIAGE
HALF
7. CAM
B
Inboard Midflap Carriage Installation Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-14
ALL ú ú 01 Page 402 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
4. TORQUE SHAFT
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(14)
