(2)  
D00633 Grease - BMS 3-33 (Recommended)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-07
 ALL  ú ú 02 Page 404 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 B.
C.
D.
A
737-300/400/500MAINTENANCE MANUAL
 (3)
D00013 Grease - MIL-G-23827 (Alternate)References

 (1)
27-51-00/201, Trailing Edge Flap Systems

 (2)
27-51-32/401, Inboard Flap Track FairingsAccess

 (1)
Location Zone

 309, 409 Wing Trailing Edge Inboard Flap and SpoilersProcedure
 S 224-011
 (1)  If you will install used parts, do this task: Inspection" (Ref 27-51-07/601). "Inboard Foreflap
 S 424-012
 (2)  Install the foreflap: (a) Put the foreflap on the toggle. (b) Install the pivot rollers: 1) Put the bushing in the pivot roller. 2) Install the washer and nut on the pivot roller. 3) Tighten the nut to 50-100 pound-inches. 4) Install the cotter pin.
 S 434-013
 (3)  Attach the three foreflap tracks to the foreflap: (a) Cut the shims to fit the clearances between the foreflap track and the track attach fitting. 1) The maximum permitted clearance between the foreflap track and the attach fitting is 0.002 inch with the shims installed.
 (b) (c) (d)  Apply the primer to the shims.Install the shims with the primer wet.Install the two track attach bolts to attach the track to the attach fitting: 1) Apply a layer of the grease to the bolts. 2) Install the bolt, washer and nut. 3) Foreflap tracks can be temporarily attached to the flap.
 S 434-014
 (4)  Install the bolt that attaches the exhaust gate actuation mechanism to the foreflap. (a) Tighten the nut.
 S 864-015
 (5)  Do this task to pressurize hydraulic systems A and B: Hydraulic System" (Ref 27-51-00/201). "Pressurize
 S 864-016
 (6)  Move the flap control lever to the UP detent.
 S 864-017
 (7)  Move the speed brake lever to the UP position to lift the spoilers.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-07
 ALL  ú ú 02 Page 405 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 864-018
 (8)  
Do this task to depressurize hydraulic systems A and B: "Depressurize Hydraulic System" (Ref 27-51-00/201).

 S 224-019

 (9)  
Make sure the clearance between the trailing edge of the foreflap and the upper surface of the midflap is 0.13 +0.07/-0.08 inch (Section A-A).

 (a)  
If the clearance is not in the tolerance, add or remove the shims between the foreflap and the track attach fitting.

 (b)  
Apply the primer to the shims.

 (c)  
Tighten the track attach fitting bolts.

 (d)  
Install the cotter pin if applicable.

 S 214-020
 (10)
 With the flaps retracted, make sure the bulb seal on the lower forward edge of the ground spoiler is compressed 0.10 to 0.20 inch.

 (a)  
Adjust the seal retainer if it is necessary.

 (b)  
Lower the spoilers: 1) Do this task to pressurize hydraulic system A "Pressurize Hydraulic System" (Ref 27-51-00/201). 2) Move the speed brake lever to the DOWN position to lower the spoilers.

 3)  Do this task to depressurize hydraulic system A "Depressurize Hydraulic System" (Ref 27-51-00/201).
 S 434-021
 (11) Do this task:  "Inboard Flap Track Fairing Installation" (Ref 27-51-32/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-07
 ALL  ú ú 01 Page 406 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(9)