(2)  
27-51-32/401, Inboard Flap Track Fairing

 B.  
Access

 (1)  
Location Zone
 216, 217 Main Wheel Well

 C.  
Procedure

 S 864-004
 (1)  
Pressurize the hydraulic system B (Ref 27-51-00/201).

 S 864-005

 (2)  
Put the flap control lever in the UP detent to retract the flaps.

 NOTE: If the flap power unit does not operate, you must disconnect
____ the torque tubes from the power unit. Manually turn the torque tubes to retract the flaps.
 S 864-006
 (3)  
Depressurize the hydraulic system B (Ref 27-51-00/201).

 S 864-007

 (4)
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6 Panel
 1) ALT TE FLAP DRIVE AC

 (5)
Remove the inboard flap track fairings (Ref 27-51-32/401).

 S 034-009

 (6)  
Disconnect the electrical connector from the flap alternate drive unit (Fig. 401).

 (7)
Remove the lower pan from the flap control unit (Fig. 402).

 S 014-008
 S 014-010
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-54
 ALL  ú ú 01 Page 401 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 484-002
 CAUTION: DO NOT PRESSURIZE THE HYDRAULIC SYSTEMS WITH THE RIG PIN F-1
_______ INSTALLED. YOU CAN CAUSE DAMAGE TO THE FLAP CONTROL UNIT.
 (8)  
Install the rig pin F-1 in the flap control unit.

 S 034-011

 (9)
Disconnect the torque tubes from the flap power unit (Fig. 401):

 (a)  
Remove the screws that attach the sleeves on the torque tubes to the coupling on the flap power unit.

 (b)  
Move the sleeves off the couplings and disconnect the torque tubes.

 S 034-012
 (10)
 Disconnect the hydraulic lines from the flap hydraulic motor:

 (a)  
Disconnect the hydraulic lines.

 (b)  
Install plugs in the hydraulic lines and ports.

 S 034-013
 (11)
 Disconnect the WFFA and WFFB cables from the flap power unit:

 (a)  
Turn the turnbuckles to loosen the cables.

 (b)  
Remove the cables from the flap power unit.

 (c)  
Install a tag on the cables to identify them.

 S 024-014
 (12)
 Remove the flap power unit (Fig. 401):

 (a)  
Disconnect the bonding jumper from the mounting bracket for the flap power unit.

 (b)  
Remove the bolts that attach the flap power unit to the mounting bracket.

 (c)  
Remove the flap power unit from the airplane.

 (d)  
Remove the flap alternate drive unit from the flap power unit.

 (e)  
Remove the flap hydraulic motor from the flap power unit.

 TASK 27-51-54-404-015
 3. Flap Power Unit Installation
____________________________
 A. Special Tools and Equipment
 (1)  
F70300-1 Flap Drive Adapter

 (2)  
Rig Pin (F-1) - 0.311 +0.000/-0.002 inch diameter 3.40 +/-0.06 inch long (MS20392-4)

 NOTE: The rig pin is a part of the kit F70207-69, -78, or -83.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-54
 ALL  ú ú 03 Page 402 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
FWD
FLAP ALTERNATE DRIVE UNIT 
WFA CABLE  WFFB CABLE WFFA CABLE  SEE  B  TUBE TORQUE 
LE FLAP CONTROL VALVE FLAP CONTROL UNIT SOLENOID VALVE FLAP LOAD LIMITER CONTROL VALVE TE FLAP  BYPASS VALVE TE FLAP  UNIT FLAP POWER 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(90)