E.  
Procedure

 S 434-015
 (1)  
If you will install a different midflap:

 (a)  
Install the fairing support arms on the flap carriages (Fig. 402).

 (b)  
Attach the fairing support pushrods to the fairing support arms: 1) Make sure the initial length of the fairing support

 pushrods is 7.40 +/-0.10 inch. 2) Put the fairing support pushrods in the correct position on
 the fairing support arms. 3) Install the bolt, washer and nut. 4) Tighten the nuts and install the cotter pins.
 CAUTION: INSTALL THE BOLTS WITH THE HEADS UP AND DO NOT INSTALL
_______ WASHERS ON BOLTS HEAD. THE INCORRECT BOLT DIRECTION OR INSTALLATION OF THE WASHER CAN CAUSE DAMAGE TO THE MIDFLAP AND AFTFLAP.
 (c)  
Connect the aft pushrods to the aftflap with the bolt heads up. 1) Tighten the nuts and install the cotter pins.

 (d)  
Install the carriage bearing support on the midflap (Fig. 402): 1) Apply a thick layer of the grease on the slotted hole and bearing on the aft end of the carriage spindle.

 2)  Put the carriage bearing support on the end of the carriage with the shims on the midflap.
 NOTE: Make sure the shims are the correct thickness.
____
 3) Apply a layer of the sealant on the bolts.
 4) Install the bolts, washers and nuts to attach the carriage

 bearing support to the midflap. 5) Tighten the 1/4 inch nuts to 50-70 pound-inches. 6) Tighten the 5/16 inch nuts to 100-140 pound-inches.
 S 494-016
 CAUTION: MAKE SURE THE CABLES ON THE SLING DO NOT TOUCH THE TRAILING
_______ EDGE OF THE SPOILERS. THE CABLES CAN CAUSE DAMAGE TO THE SPOILERS. DISCONNECT THE SPOILERS AND MOVE THEM FORWARD IF IT IS NECESSARY.
 (2)  Install the sling assembly to hold the flap.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-34
 ALL  ú ú 02 Page 408 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 
737-300/400/500MAINTENANCE MANUAL
 S 424-017
 (3)  Install the outboard flap (Fig. 401):
 (a) With the forward toggle rollers in the track, move the flap
 carriages forward on the track.
 (b) With the flap carriages near the aft end of the track, measure
 the clearance between the flap track and the carriage roller
 bolts.
 (c) If the clearance is less than 0.050 inch, adjust the rollers:
 1) Remove the flap from the tracks.
 2) Remove the bolts for the rollers.
 3) Add the shims below the heads of the bolts to increase the
 clearance.
 4) Install the nut.
 5) Install the cotter pin. Make sure it does not extend past
 the end of the bolt.
 (d) Move the flap forward on the tracks.
 S 434-018
 (4)  Install the carriage stops on the flap tracks:
 (a) Put the stop in its position on the lower surface of the flap
 track.
 (b) Move the flaps aft.
 (c) Lift the flap until the airload rollers touch the flap track.
 (d) Make sure the clearance between the carriage and the carriage
 stop is a minimum of 0.06 inch.
 (e) Move the flaps fully aft.
 (f) Make sure the deadweight rollers touch the flap track.
 (g) Make sure the carriage and the carriage stop touch for a
 minimum of 0.05 inch.
 (h) Move the flap forward.
 (i) Install the lockwire on the bolts that attach the carriage
 stops.
 S 434-019
 (5)  Do this task: "Outboard Foreflap Installation" (AMM 27-51-37/401).
 S 094-020
 (6)  Remove the sling assembly from the outboard flap.
 S 824-021
 (7)  Move the flap until the sequencing carriage engages the stop and the
 deadweight rollers touch the top surface of the flap track.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-34
 ALL  ú ú 01 Page 409 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(39)