(2)  
27-51-52/501, Outboard Flap Track Fairings

 (3)  
27-51-52/601, Outboard Flap Track Fairings

 (4)  
29-15-00/201, Hydraulic System A, B, and Standby

 B.
Access

 (1)  
Location Zones 307, 407 Wing Trailing Edge, Outboard Flap and Spoilers

 (2)  
Access Panels
 Center Fairing Access Panel

 C.
Prepare to Install the Center Fairing

 S 224-014
 (1)  
If used parts will be used to install the flap track fairing, do this task: "Outboard Flap Track Fairing Inspection" (Ref 27-51-52/601).

 S 434-015

 (2)  
If it is necessary, install the cam track of the aftflap drive mechanism:

 (a)  
Do this task: "Trailing Edge Flap System Activation" (Ref 27-51-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-52
 ALL  ú ú 03 Page 405 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 WARNING:_______ MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL
 CONTROL SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER.
 AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING
 GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU
 SUPPLY HYDRAULIC POWER.  THIS CAN CAUSE INJURY TO PERSONS

 AND DAMAGE TO EQUIPMENT.
 (b) Do this task to pressurize hydraulic system B: "Pressurize Hydraulic System A, B, or Standby" (Ref 29-15-00/201).
 WARNING:_______ MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE
 TRAILING EDGE FLAPS, THE LEADING EDGE FLAPS AND SLATS AND
 THE DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL
 LEVER.  THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO

 EQUIPMENT.
 (c)  
Move the flap control lever to the flaps position 0 (flaps up) detent to retract the flaps.

 (d)  
Do this task to depressurize hydraulic system B: "Depressurization of Hydraulic System A, B, or Standby" (Ref 29-15-00/201).

 (e)  
Measure and make a record of the distance between the fairing pivot point and the bellcrank pivot point (Fig. 401). Identify this dimension as dimension Y.

 (f)  
Do this task to pressurize hydraulic system B: "Pressurize Hydraulic System A, B, or Standby" (Ref 29-15-00/201).

 (g)  
Move the flap control lever to the flaps position 40 (flaps down) detent to extend the flaps.

 (h)  
Do this task to depressurize hydraulic system B: "Depressurization of Hydraulic System A, B, or Standby" (Ref 29-15-00/201).

 (i)  
Do this task: "Trailing Edge Flap System Deactivation" (Ref 27-51-00/201).

 (j)  
Install the cam track of the aftflap drive mechanism in the center fairing: 1) Install tapered shims and fasteners to hold the cam track

 in its position.
 NOTE: Use the tapered shims that were installed before.
____
 a)  Set the cam tracks on the serrated plates with the bolts in the center of the slotted holes in the cam track.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-52
 ALL  ú ú 01 Page 406 ú Nov 15/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 2)  Do a check of the cam track position in relation to the bell crank pivot point: a) Measure and make a record of the distance between the
 forward end of the cam track and the fairing pivot point (Fig. 401). Identify this dimension as dimension
 X.
 b)  Subtract the value for dimension Y from the value for dimension X.
 NOTE: The difference between the values of X and Y
____ must be 6.10 to 6.46 inches.
 c)  If the difference between the values of X and Y is out of the tolerance, adjust the cam track.
 NOTE: Move the cam track forward or aft until the
____ difference between the values of X and Y is in the tolerance.
 3)  Do a check that the cam track is aligned with the fairing track: a) Put a straightedge across the fairing tracks near the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(84)