Subtask 54-54-00-860-050
 C. Aircraft Maintenance Configuration
 (1)
 Put the related hydraulic system in the pressurized configuration before the maintenance action (Ref. TASK 29-00-00-864-001)

 (2)
 Depressurize the hydraulic reservoir (Ref. TASK 29-14-00-614-001)

 Subtask 54-54-00-040-051

 D. Aircraft Maintenance Configuration
 (1)
 Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041). Subtask 54-54-00-010-050

 E. Get Access
 (1)
 Put the access platform in position:

 (a)
 at the zone 470 for the left pylon

 (b)
 at the zone 480 for the right pylon

 (2)
 Remove these panels :

 (a) For the left pylon 471CL, 475BL, 476BR.

 (b)
 for the right pylon 482CR, 486BR, 485BL. Subtask 54-54-00-020-050

 F. Removal of the Fairing
 (1) Remove the aft movable fairing (Ref. TASK 54-55-00-000-001).

 (2)
 Remove the lower fairing (Ref. TASK 54-56-00-000-001). Subtask 54-54-00-020-052

 G. Removal of the Hydraulic Lines
 (Ref. Fig. 401/TASK 54-54-00-991-001)

 WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
 (1)
 Remove the nut (6) and the bolt (5).

 (2)
 Remove the lines (1), (2), (3) and (4).

 (3)
 Put a container capacity in position to collect the hydraulic fluid.

 (4)
 Disconnect the drain lines (7) and (8).

 (5)
 Put blanking plugs on the disconnected line ends.

 Installation of the Hydraulic Lines
 Figure 401/TASK 54-54-00-991-001
 1EFF :  ALL  1  54-54-00 Page 404 
1  1  Feb 01/98
 1  1
 1CES  1

 4. Procedure
_________

 Subtask 54-54-00-020-053
 A. Removal of the Aft Fixed Fairing
 (Ref. Fig. 402/TASK 54-54-00-991-002)

 (1)
 Remove the screw (24) and the washer (23).

 (2)
 Disconnect the bonding lead (22).

 (3)
 Remove the nut (19), the washer (20) and the bolt (21).

 (4)
 Remove the nut (15) and the bolt (13).

 (5)
 Remove the nut (17), the washer (18), the bolt (16) and the washer (14).

 (6)
 Loosen the nuts (9) and (12).

 (7)
 Remove the nuts (11) and the bolts (10).

 (8) Remove the aft fixed fairing. R NOTE : Two persons are necessary to move the aft fixed fairing.
____

R  Attach Fittings on the Aft Fixed Fairing Figure 402/TASK 54-54-00-991-002
 1EFF : 1 1 1CES  ALL  1 111 54-54-00 Page 406 Aug 01/99

R TASK 54-54-00-000-001- 01

R  Removal of the Aft Fixed Fairing 
R  WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ 
R  START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  1. Reason for the Job__________________ 
R  This is an alternative method without removal of the hydraulic lines. 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific blanking plugs 
R  No specific warning notice 
R  No specific access platform 1.5 m (4 ft. 11 in.) 
R  B. Referenced Information 
R  -------------------------------------------------------------------------------
R  REFERENCE DESIGNATION 
R  -------------------------------------------------------------------------------
R  54-55-00-000-001 Removal of the Aft Movable Fairing 
R  54-56-00-000-001 Removal of the Lower Fairing 
R  78-30-00-481-041 Make the Thrust Reverser Unserviceable for 
R  Maintenance 
R  54-54-00-991-009 Fig. 403 
R  54-54-00-991-007 Fig. 404 
R  54-54-00-991-008 Fig. 405

R  3. Job Set-up__________ 
R  Subtask 54-54-00-941-054 
R  A. Safety Precautions 
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護(hù)手冊 AMM NACELLES/PYLONS(90)