(2)
Before installation, make sure that the lockwashers (25) and the nuts
(26)
are in correct condition. If necessary, replace the lockwashers
(25)
and the nuts (26).
Subtask 54-51-17-420-054
B. Installation of the Pylon-to-Wing Forward Attach Fitting
(Ref. Fig. 404/TASK 54-51-17-991-005)
(1)
Apply the COMMON GREASE (Material No. 04-004) to the sleeves, the spigot and all the friction surfaces.
(2)
Put the shackles (29) in position.
1EFF : ALL 1 54-51-17Page 414 1 1 May 01/03R 1 1 1CES 1
(3) Install the sleeves (24). Install the top sleeve first.
NOTE : You can install the sleeve more easily if you change the force____ that the jack applies to the attach fitting.
R R R R R NOTE : Put the nuts, the cotter pins and the lockwashers:____ - for the upper attachments, in the outer side of the pylons (always symmetrically to the pylon centerline). - for the inner attachments, in the inner side of the pylons (always symmetrically to the pylon centerline).
(4) Install the lockwashers (25).
(5) Install the nut (26). Lock the sleeve (24) with an special wrench of the PYLON REMOVAL-WRENCH (98D54503000000). Torque the nut (26) to between 4 and 5 m.daN (29.49 and 36.87 lbf.ft). Use a pin wrench of the PYLON REMOVAL-WRENCH (98D54503000000) and a torque wrench.
(6) Safety the nut (26) with the lockwasher (25).
(7) Install the bolts (23).
(8) Lock the bolts (23) with a pin wrench of the PYLON REMOVAL-WRENCH (98D54503000000) and install the nut (27) with a pin wrench of the PYLON REMOVAL-WRENCH (98D54503000000) .
(9) Torque the nut (27) to between 4 and 5 m.daN (29.49 and 36.87 lbf.ft).
(10) Safety the nuts (27) with the cotter pins (28).
Subtask 54-51-17-081-050
C. Removal of a Dynamometric Cell and Jack Under the Attach Fitting
(1) Remove the force applied to the jack. Remove the jack from under the attach fitting at RIB1.
(2) Remove the dynamometric cell and the ADAPTOR - DYNAMOMETRIC AT RIB 1 (98A54403024001).
5. Close-up
________ Subtask 54-51-17-420-055
A. Connection of the Fuel/Defuel System at RIB09
(Ref. Fig. 403/TASK 54-51-17-991-003)
(1)
Put the clamp (16) in position on the sleeves (8).
(2)
Install the new O-ring (11) on the nut (2).
(3)
Install the nuts (2).
(4)
Install the ring-retainer (3) and the ring-retainer (4) on the connectors (12).
(5)
Install the nuts (12) on the nuts (2).
(6)
Install the nut (13) on the connectors (12).
(7)
Install the O-ring (14) on the nut (13).
(8)
Install MISCELLANEOUS (Material No. 19-010) on the connectors (12).
(9)
Install the O-rings (15) on the clamp (16).
(10)
Install the bonding braids (1), the bolts (9), the nuts (10) and tighten the nuts (10).
(11)
Install the ring retainers (5), the bolts (7), the nut (6), and tighten the nuts (6).
Subtask 54-51-17-420-056
B. Installation of the Temperature Sensor and the Rods
(Ref. Fig. 401/TASK 54-51-17-991-001, 402/TASK 54-51-17-991-012)
(1)
Install the rods (5), the bolts (4), the washers (3) and the nuts (2). Tighten the nuts.
(2)
Safety the nuts (2) with the cotter pins (1).
(3)
Remove the blanking caps from the electrical connectors. Connect the temperature sensor (6).
-
For the left pylon : 6HA1
-
For the right pylon : 6HA2.
1EFF : ALL 1 54-51-17Page 416 1 1 May 01/03R 1 1 1CES 1
Subtask 54-51-17-586-050
C. Aircraft Lowering
(1)
Lower the aircraft (Ref. TASK 07-11-00-586-002). Subtask 54-51-17-410-050
D. Installation of the Panels
(1) Install the access panels :
(a) For the left pylon : 471AL, 472AR, 414FR 521BT, 521HB.
(b)
For the right pylon : 481AL, 482AR, 423FL 621BT, 621HB. Subtask 54-51-17-420-057
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(55)
