(23)
Depressurize the actuating cylinder.
(24)
Remove the nuts (21) and the six threaded rods (22).
(25)
Remove the bolts (13) and (14).
(26)
Remove the two half shells (11) and (12).
R (27) Tighten the nut (34) so that the jaws (33) touch the spigot ball R joint.
(28)
Pressurize the actuating cylinder so that the sliding rod comes out fully.
(29)
Install the two half segments (31) and (36) between the wing and the pylon, in the spigot ball joint bore.
NOTE : Is is mandatory to install the half segments (31) and (36). If
____ you do not install them, damage to the pylon can occur.
(30)
Depressurize the actuating cylinder and pull in the sliding rod by 40 mm (1.5748 in.).
(31)
Install the shim (35) between the sliding rod end and the plate (26).
(32)
Pressurize the actuating cylinder and fully remove the ball joint
(32) from its housing.
(33)
Depressurize the actuating cylinder and remove the shim (35).
(34)
Loosen the nuts (34) so that the jaws (33) are in the open position.
(35)
Remove the actuating cylinder, the nuts (25), the plate (26) and the studs (24).
NOTE : The two half segments (31) and (36) must stay in position in
____
the ball joint bore.
TASK 54-51-41-400-001
Installation of the Spigot Ball Joint
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
98D54403002000 1 R/I TOOL - SPIGOT BALL JOINT
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R Material No. 08-034 Material No. 09-016 Material No. 09-018 Material No. 09-025 Material No. 11-004 Material No. 19-003 USA MIL-R-46082 ADHESIVE (Ref. 20-31-00) USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)USA AMS 3267/3 CORROSION INHIBITING LOW ADHESION SEALANT (Ref. 20-31-00) USA MIL-PRF-81733 CORROSION INHIBITING SEALANT SPRAYABLE (Ref. 20-31-00)USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R 1EFF : ALL 1 54-51-41Page 414 1 1 May 01/05 1 1 1CES 1
C. Expendable Parts -------------------------------------------------------------------------------
FIG.ITEM --------- |DESIGNATION ---------------------------------------- |IPC-CSN------------------------------
1 bolts 54-51-17 02B-050
D. Referenced Information
------------------REFERENCE -------------------------------DESIGNATION ------------------------------
-------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power
26-21-41-000-004 Removal of the Cartridge of the Engine Fire-Extinguisher Bottle
26-21-41-400-004 Installation of the Cartridge of the Engine Fire-Extinguisher Bottle
78-30-00-081-041 Make the Thrust Reverser Serviceable after Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
54-51-41-991-001-A Fig. 401
54-51-41-991-004-A Fig. 405
54-51-41-991-005-A Fig. 406
3. Job Set-up__________
Subtask 54-51-41-860-051
A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized (Ref. TASK 24-42-00-861-001).
(2)
Make sure that the access platforms are in position.
(3)
Make sure that the fire extinguisher bottles are removed (Ref. TASK 26-21-41-000-004).
1EFF : ALL 1 54-51-41Page 415 1 1 May 01/05R 1 1 1CES 1
Subtask 54-51-41-040-051
B. Aircraft Maintenance Configuration
(1) Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041) .
Subtask 54-51-41-914-050
C. Preparation of the Replacement Component
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(77)
