AFT FIXED FAIRING - DESCRIPTION AND OPERATION
_____________________________________________
1. Description
___________
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-212,
(Ref. Fig. 001)
R **ON A/C 106-149, 213-299, 301-399, 401-499,
(Ref. Fig. 001A)
**ON A/C ALL
The fixed fairing is attached at two points to the pylon box at RIB10 and
one point to the wing at rear false spar.
The fixed fairing is composed of:
-six ribs made of light alloy sheet
-two skin panels made of light alloy sheet
-three longitudinal "members" made of light alloy sheet
-two access panels made of carbon and honeycomb (sandwich panel).
All the access panels are bolted.
Standard attachement is made by aluminum alloy rivets.
Fixed Fairing
Figure 001 (SHEET 1)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 54-54-00Page 2 1201-212, 1May 01/05 1 1 1CES 1
Fixed Fairing
Figure 001 (SHEET 2)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 54-54-00Page 3 1201-212, 1May 01/05 1 1 1CES 1
Fixed Fairing
Figure 001A (SHEET 1)
R 1EFF : 106-149, 213-299, 301-399, 401-499, 1 54-54-00Page 4 1 1 Aug 01/05 1 1 1CES 1
Fixed Fairing
Figure 001A (SHEET 2)
R 1EFF : 106-149, 213-299, 301-399, 401-499, 1 54-54-00Page 5 1 1 Aug 01/05 1 1 1CES 1 AFT FIXED FAIRING - REMOVAL/INSTALLATION
________________________________________
TASK 54-54-00-000-001
Removal of the Aft Fixed Fairing
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
R There is an alternative method for this procedure. This task gives one of R the methods. For the other method, refer to the other task in this page R block.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific access platform 1.5 m (4 ft. 11 in.)
No specific container capacity 3 l (0.7925 USgal)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action
29-00-00-910-002 Safety Procedures of the Hydraulic System
29-14-00-614-001 Depressurization of the Hydraulic Reservoirs
54-55-00-000-001 Removal of the Aft Movable Fairing
54-56-00-000-001 Removal of the Lower Fairing
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
54-54-00-991-001 Fig. 401
54-54-00-991-002 Fig. 402
3. Job Set-up
__________
Subtask 54-54-00-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU HYD/HYD PWR/B WARN/& CTL 2702GJ C12 121VU HYDRAULIC/HYD POWER/Y 3803GX N30 123VU B HYD/ELEC PUMP 2701GJ AB09 123VU Y HYD/ELEC/PUMP 3802GX AB06
R 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
Subtask 54-54-00-941-050
B. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
On the overhead maintenance panel 50VU:
(a)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b)
Put a warning notice to tell persons not to energize the FADEC 1(2).
(4)
Obey the safety procedures of the hydraulic system (Ref. TASK 29-00-00-910-002)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(89)
