R 1EFF : ALL 1 54-51-00Page 662 1 1 Aug 01/03 1 1 1CES 1
Shackles, Sleeves and Bolts of the Pylon-to-Wing Attachment Fittings at RIB4 Figure 613/TASK 54-51-00-991-062
1EFF : ALL 1 54-51-00Page 663 1 1 Aug 01/03R 1 1 1CES 1
(2) Make sure that there is no:
R R R (a) Corrosion damage: - If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200-P.Block001) for types of corrosion, inspection, removal and corrosion protection.
R R R (b) Other damage (cracks, scratches, stress, marks, dents, bumps,...): - If you find other damage, refer to the Structural Repair Manual (Ref. SRM 511100-P.Block001) for damage classification and associated corrective action.
5. Close-up________
Subtask 54-51-00-420-055
R A. Installation of the Components
(1) Install the bolts, the sleeves and the shackles (Ref. TASK 54-51-17-400-001).
Subtask 54-51-00-410-060
B. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Remove the access platform(s).
R (3) Remove the warning notice(s).
TASK 54-51-00-200-010
R Detailed Inspection of Pylon Spigot Receptacle Upper Surface, including Fitting R Bore, and Upper Spar Surrounding Surface
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 545117-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice R No specific access platform 2.5 m (8 ft. 2 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 54-51-21-000-001 Removal of the Pylon Lateral Access-Doors
R 54-51-21-400-001 Installation of the Pylon Lateral Access-Doors 54-51-41-000-001 Removal of the Spigot Ball Joint 54-51-41-400-001 Installation of the Spigot Ball Joint
R 78-30-00-081-041 Make the Thrust Reverser Serviceable after Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
SRM 511100-P.Block001
SRM 512200-P.Block001
54-51-00-991-009 Fig. 614
3. Job Set-up
__________
Subtask 54-51-00-941-061
A. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
On the overhead maintenance panel 50VU:
(a)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b)
Put a warning notice to tell persons not to energize the FADEC.
Subtask 54-51-00-010-060
B. Get Access
(1)
Put an access platform in position:
(a)
At zone 410 for the left pylon.
(b)
At zone 420 for the right pylon.
(2)
Remove the access panels:
(a) For the left pylon: 471AL, 471BL, 472AR, 472BR.
(b) For the right pylon: 481AL, 481BL, 482AR, 482BR. R (3) Remove the pylon lateral access-doors (Ref. TASK 54-51-21-000-001):
(a) For the left pylon: 425BL, 425BR.
(b) For the right pylon: 415BL, 415BR.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(35)
