-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
R WARNING : REMOVE, INSPECT (REPLACE IF NECESSARY), BOLTS ONE AT A TIME. FAILURE
_______ R TO DO THIS COULD CAUSE INJURY OR DEATH.
1. Reason for the Job
__________________
Refer to the MPD TASK: 545101-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
No specific access platform 2.5 m (8 ft. 2 in.)
No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-047 C Z-11.904
ANTI COR. COMPOUND(HIGH TEMP.SILICONE SEALANT)
(Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
78-36-00-010-040 Opening of the Thrust Reverser Doors
78-36-00-410-040 Closing of the Thrust Reverser Doors
NTM 545101,P.Block-601
SRM 511100,P.Block 001 (for corrective action)
SRM 512200,P.Block 001 (for corrective action)
54-51-00-991-053 Fig. 601
54-51-00-991-057 Fig. 602
3. Job Set-up
__________
Subtask 54-51-00-941-050
A. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
R (3) On the overhead maintenance panel 50VU:
(a)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b)
Put a warning notice to tell persons not to energize the FADEC.
Subtask 54-51-00-010-050
B. Get Access
R (1) Open the fan cowl doors (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR.
R (2) Open the thrust reverser doors (Ref. TASK 78-36-00-010-040) FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR.
R (3) Put an access platform in position:
R (a) At zone 410 for the left pylon.
R (b) At zone 420 for the right pylon.
Subtask 54-51-00-040-051
C. Aircraft Maintenance Configuration
(1) Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
Subtask 54-51-00-020-061
RR D. Removal of the Components (Ref. Fig. 601/TASK 54-51-00-991-053)
R R WARNING : REMOVE, INSPECT (REPLACE IF NECESSARY), BOLTS ONE AT A TIME._______ FAILURE TO DO THIS COULD CAUSE INJURY OR DEATH.
R (1) Remove the nut (3), the bolt (1) and the washer (2).
R R NOTE : Do the full procedure for one hole, then do it again for each____ hole.
R
R Fitting at RIB1 Figure 601/TASK 54-51-00-991-053
1EFF : 1 1 1CES ALL 1 111 54-51-00 Page 604 Feb 01/01
Subtask 54-51-00-110-051
E. Preparation of the Inspection Area
(Ref. Fig. 602/TASK 54-51-00-991-057)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(21)
