-COMPONENTS THAT MOVE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 545104-02
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
 No specific access platform 1.5 m (4 ft. 11 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004  USA MIL-T-81533
 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
 (Ref. 20-31-00)

 Material No. 19-003  USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 54-51-21-000-001 Removal of the Pylon Lateral Access-Doors R 54-51-21-400-001 Installation of the Pylon Lateral Access-Doors R
 78-30-00-081-041 Make the Thrust Reverser Serviceable after
 Maintenance
 78-30-00-481-041 Make the Thrust Reverser Unserviceable for

 Maintenance
 NTM 545104,P.Block-901
 SRM 511100,P.Block 001 (for corrective action)
 SRM 512200,P.Block 001 (for corrective action)
 54-51-00-991-056 Fig. 607

 3. Job Set-up
__________
 Subtask 54-51-00-941-055

 A. Safety Precautions
 (1)
 On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2)
 Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3)
 On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
 (b) Put a warning notice to tell persons not to energize the FADEC. Subtask 54-51-00-010-054
 B. Get Access
 (1) Put an access platform in position:
 (a)
 At zone 470 for the left pylon.

 (b)
 At zone 480 for the right pylon.

R (2) Remove the pylon lateral access-doors (Ref. TASK 54-51-21-000-001):

 (a)
 For the left pylon: 415AL, 415AR, 415BL, 415BR.

 (b)
 For the right pylon: 425AL, 425AR, 425BL, 425BR.

 Subtask 54-51-00-040-056
 C. Aircraft Maintenance Configuration
 (1) Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
 Subtask 54-51-00-110-056
 D. Preparation of the Inspection Area
 (Ref. Fig. 607/TASK 54-51-00-991-056)

 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
 (1)
 Clean the inspection area with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003), if necessary.

 (2)
 Make sure that the surface of the inspection area is clean and smooth.

 (3)
 Do a visual check of the inspection area for damage or
 discontinuities.

 (4)
 Make sure that there is no:

 (a) Corrosion damage:
 -If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200,P.Block 001) for types of corrosion, inspection, removal and corrosion protection.

R Lower Spar between RIB1 and RIB2, RIB3 and RIB4, and RIB8 and RIB10 -R Inspection Areas Figure 607/TASK 54-51-00-991-056

 (b) Other damage (cracks, scratches, stress, marks, dents, bumps...):
 -If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100,P.Block 001) for damage classification and corrective action.
 4. Procedure
_________
 Subtask 54-51-00-250-052

 A. Inspection
 (Ref. Fig. 607/TASK 54-51-00-991-056)

 (1)
 Do a special detailed inspection of the upper surface of the pylon lower spar between RIB1 and RIB2, RIB3 and RIB4, and RIB8 and RIB10. Refer to the Non-destructive Testing Manual (Ref. NTM 545104,P.Block-901).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(28)