曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R R R  (1) Clean the inspection surface with CLEANING AGENTS (Material No. 11-004) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if necessary.
 4. Procedure_________
 Subtask 54-51-00-220-075
 A. Inspection (Ref. Fig. 628/TASK 54-51-00-991-063)
R R  (1) Do a special detailed inspection of the pylon-to-wing aft attachment-shackles at RIB10. Refer to the Non-destructive Testing Manual (Ref. NTM 545123, P.Block 401).
 (2) Make a report of the damage after the NDT inspection:
R R  (a) Corrosion damage: - If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200-P.Block 001) for types of corrosion, inspection, removal and corrosion protection. 
R R R R R  (b) Other damage (cracks, scratches, stress, marks, dents, bumps,...): - If you find other damage, refer to the Structural Repair Manual (Ref. SRM 511100-P.Block 001) for damage classification and related corrective action. 

R 1EFF : ALL 1 54-51-00Page A642 1 1 May 01/05 1 1 1CES 1

 Pylon-to-Wing Aft Attachment Shackles at RIB10 Figure 628/TASK 54-51-00-991-063 
R 1EFF : 1 1 1CES  ALL  1 111 54-51-00 Page A643 May 01/05

 

 5. Close-up________
 Subtask 54-51-00-440-072
 A. Aircraft Maintenance Configuration
 (1) Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
 Subtask 54-51-00-410-077
 B. Close Access 
R  (1) Install the panels: 
R  (a) For the left pylon: 471CL, 472BR, 475AL, 475BL, 476AR, 476BR. 
R  (b) For the right pylon: 481BL, 482CR, 485AL, 485BL, 486AR, 486BR.
 (2) Make sure that the work area is clean and clear of tool(s) and other items.
 (3) Remove the access platform(s).
R  (4) Remove the warning notice(s). 

R 1EFF : ALL 1 54-51-00Page A644 1 1 May 01/05 1 1 1CES 1 PYLON-TO-WING ATTACH FITTINGS - REMOVAL/INSTALLATION

____________________________________________________
 TASK 54-51-17-000-001
 Removal of the Pylon-to-Wing Forward Attach Fitting at RIB4
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT YOU HAVE THE CORRECT FIRE FIGHTING EQUIPMENT
_______ AVAILABLE.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific warning notice No specific access platform 1.5 m (4 ft. 11 in.) No specific dynamometric cell 400 kg (881.8488 lb) 98D54003005000 1 PYLON SHAFT EXTRACTOR RIB 4/RIB 10 98D54403000000 1 DUMMY SHACKLES - PYLON TO WING YOKES 98D54403001000 1 DUMMY SLEEVES - PYLON TO WING YOKES 98D54503000000 1 PYLON REMOVAL-WRENCH

 B. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
05-57-00-200-001 Aircraft Stability 07-11-00-581-001 Lifting for Aircraft Maintenance Operations 28-00-00-910-001 Fuel Safety Procedures 71-00-00-000-042 Removal of the Power Plant 71-13-11-000-040 Removal of the Fan Cowl Doors 78-32-11-000-040 Removal of the Left or Right Half Door of Thrust
 Reverser 54-51-17-991-001 Fig. 401 54-51-17-991-012 Fig. 402 54-51-17-991-003 Fig. 403 54-51-17-991-005 Fig. 404
 3. Job Set-up
__________
 Subtask 54-51-17-860-050
 A. Safety Precautions
 (1)
 On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2)
 Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3)
 On the overhead maintenance panel 50VU:

 (a)
 Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b)
 Put a warning notice to tell persons not to energize the FADEC 1(2).

 

 (4)
 Obey the fuel safety procedures (Ref. TASK 28-00-00-910-001) when you do work on the fuel system.

 Subtask 54-51-17-869-050
 B. Aircraft Stability
 (1) Let the aircraft become stable (Ref. TASK 05-57-00-200-001).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(52)