(a) Put a warning notice to tell persons not to start the engine.

 (2)
 Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3)
 On the overhead maintenance panel 50VU:

 (a)
 Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b)
 Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 54-51-17-010-055
 C. Get Access
 (1) Put an access platform in position:
 (a) For the left pylon at the zone 470.
 (b) For the right pylon at the zone 480. Subtask 54-51-17-020-063
 D. Removal of the Components
 (1) Remove the shackles at RIB10 (Ref. TASK 54-51-17-000-002).

 4. Procedure
_________

 (Ref. Fig. 801/TASK 54-51-17-991-014) Subtask 54-51-17-020-064
 A. Removal of the Bushes
 (1)
 Remove and discard the bushes (2) and (3) from the shackles (1).

 (2)
 Clean the shackles (1) with CLEANING AGENTS (Material No. 11-003) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).

 Subtask 54-51-17-220-069
 B. Inspection of the Shackle Bores
 (1)
 Do a visual inspection of the shackle bores.

 (2)
 Make sure that there is no damage and that diameters D1 and D2 of the shackle bores are in the tolerance.

 (3)
 If there is damage or if diameter(s) D1 and/or D2 is(are) not in the tolerance:

 (a) Rebore the shackles (1) to the repair dimension(s) R1 and/or R2. Subtask 54-51-17-420-063
 C. Installation of the Bushes
 (1)
 Make sure that the surface of the shackle bores is clean. If necessary, clean the surface with CLEANING AGENTS (Material No. 11-003) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).

 (2)
 Soak the new bushes (2) and bushes (3) in nitrogen liquid.

 (3)
 Install the bushes (2) and (3) in the shackles (1).

 (4)
 Apply a bead of SEALANTS (Material No. 09-016B) on the shackles (1) and the bushes (2) and (3).

 (5)
 Rebore the bushes (2) and (3) to the diameters D3 and D4 with the center-to-center distances X1, X2 and X3.

 (6) Clean the shackles (1) with CLEANING AGENTS (Material No. 11-003) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003). ________
5. Close-up
 Subtask 54-51-17-420-064
 A. Installation of the Components
 (1) Install the shackles at RIB10 (Ref. TASK 54-51-17-400-002). Subtask 54-51-17-942-057
 B. Put the aircraft back to its initial configuration.
 (1)
 Remove the warning notice(s).

 (2)
 Remove the access platform(s).

 (3)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 Subtask 54-51-17-862-050
 C. De-energize the ground service network
 (Ref. TASK 24-42-00-862-001).

 Reboring of Bushes at RIB10
 Figure 801/TASK 54-51-17-991-014- 12 (SHEET 1)
 1EFF :  ALL  1  54-51-17 Page 806 
1  1  May 01/04
 1  1
 1CES  1

 Reboring of Bushes at RIB10
 Figure 801/TASK 54-51-17-991-014- 22 (SHEET 2)
 1EFF :  ALL  1  54-51-17 Page 807 
1  1  May 01/04
 1  1
 1CES  1

 PYLON-TO-ENGINE ATTACH FITTINGS - REMOVAL/INSTALLATION
______________________________________________________
 TASK 54-51-18-000-001
 Removal of the Pylon-to-Engine Aft Attach-Fittings

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
 No specific access platform 1.50 m (4 ft. 11 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R  54-51-21-000-001 Removal of the Pylon Lateral Access-Doors 71-00-00-000-042 Removal of the Power Plant 54-51-18-991-001 Fig. 401
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(69)