EFF : ALL

53-11-00Page 609

 3. Job Set-up
__________

 Subtask 53-11-00-010-068
 A. Get Access 
R  (1) Put an access platform in position at the zone 831 (841). 
R  (2) Open the forward passenger/crew door 831 (841), (Ref. TASK 52-10-00-010-001).
 Subtask 53-11-00-020-064
 B. Removal of the Component 
R R  (1) Remove the forward corner of the scuff plate from the sill of the forward passenger/crew door (Ref. TASK 53-15-15-000-001).
 Subtask 53-11-00-110-053
 C. Preparation of the Inspection Area (Ref. Fig. 603/TASK 53-11-00-991-072)
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK. 
R R R  (1) Clean the inspection area with CLEANING AGENTS (Material No. 11-004) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if necessary.
 (2) Make sure that the surface of the inspection area is clean and smooth. 
R R  (3) Do a visual check of the inspection area for damage or discontinuities.

 EFF : ALL

53-11-00Page 610
May 01/03

 Door Frame - Forward Lower Corner below Scuff Plate - Inspection Area Figure 603/TASK 53-11-00-991-072
R EFF : ALL 53-11-00Page 611 May 01/00
 CES  EFF : ALL

 (4) Make sure that there is no:
 (a) Corrosion damage: - If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200,P.Block 001) for types, inspection, removal and corrosion protection.
 (b) Other damage (cracks, scratches, stress, marks, dents, bumps...): - If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100,P.Block 001) for damage classification and corrective action.
 4. Procedure_________
 Subtask 53-11-00-270-050
 A. Inspection (Ref. Fig. 603/TASK 53-11-00-991-072) 
R R R  (1) Do a special detailed inspection of the structure of the forward lower corner below the scuff plate. Refer to the Non-destructive Testing Manual (Ref. NTM 531104,P.Block-401). 
R R  (2) Make a report of the damage after the non-destructive testing inspection:
 (a) Corrosion damage: - If you find damage, refer to the Structural Repair Manual (Ref. SRM 512200,P.Block 001) for types, inspection, removal and corrosion protection.
 (b) Other damage (cracks, scratches, stress, marks, dents, bumps...): - If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100,P.Block 001) for damage classification and corrective action.
 5. Close-up________
 Subtask 53-11-00-420-062
 A. Installation of the Component 
R R  (1) Install the forward corner of the scuff plate on the sill of the forward passenger/crew door (Ref. TASK 53-15-15-400-001)

53-11-00Page 612
May 01/03

 Subtask 53-11-00-410-068
 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
R  (2) Close the forward passenger/crew door 831 (841), (Ref. TASK 52-10-00-410-001).
 (3) Remove the access platform(s).
 EFF : ALL

53-11-00Page 613

 TASK 53-11-00-210-003
R Detailed Inspection of Forward Face of Pressure Bulkhead, Vertical Angle R (Y=675) at Crossing Areas with Horizontal Stiffeners (Z=1 and Z=1329), LH/RH
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 531107-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R No specific  access platform 3 m (9 ft. 10 in.)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004  USA MIL-T-81533
 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
 (Ref. 20-31-00)

 Material No. 19-003  USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 C. Referenced Information
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身1(39)