C. Expendable Parts -------------------------------------------------------------------------------
FIG.ITEM --------- |DESIGNATION ---------------------------------------- |IPC-CSN------------------------------
3 scuff plate 53-15-01 05 -100A
3 scuff plate 53-15-01 05 -110A
5 scuff plate 53-15-01 05 -080A
5 scuff plate 53-15-01 05 -090A
9 scuff plate 53-15-01 05 -120A
9 scuff plate 53-15-01 05 -130A
D. Referenced Information
------------------REFERENCE -------------------------------DESIGNATION ------------------------------
-------------------------------------------------------------------------------
52-10-00-410-001 Closing of the Passenger/Crew Door 53-15-15-991-001 Fig. 401 53-15-15-991-002 Fig. 402
3. Job Set-up
__________ Subtask 53-15-15-869-050
A. Aircraft Maintenance Configuration
(1) Make sure that the access platform is in position.
(2) Make sure that the applicable FWD passenger/crew door is open. Subtask 53-15-15-110-051
B. Preparation for Installation WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
EFF : ALL
53-15-15Page 405
Aug 01/01
R
CES WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
(1) Clean the contact surfaces of the scuff plates and the fuselage skin with CLEANING AGENTS (Material No. 11-003) and MISCELLANEOUS (Material No. 19-003).
R
R (2) Make sure that the scuff plates are in the correct position and are R not damaged. If necessary, replace the damaged scuff plates.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Put the vacuum equipment adjacent to the required FWD passenger/crew door.
NOTE : We recommend that you use a strong vacuum pump for attachment
____
of the scuff plates.
4. Procedure
_________
Subtask 53-15-15-420-050
A. Installation of the Scuff Plates (Ref. Fig. 401/TASK 53-15-15-991-001, 402/TASK 53-15-15-991-002)
(1) Drilling of the scuff plates NOTE : This procedure is applicable only when you install new scuff
____
plates.
(a)
Take the new scuff plates:
-
for the left passenger/crew door scuff plate (3), scuff plate
(5) and scuff plate (9).
-
for the right passenger/crew door scuff plate (3), scuff plate
(5) and scuff plate (9).
(b)
Put the scuff plates (3), (5) and (9) in position on the door sill.
(c)
Drill the attachement hole of the scuff plates to the final diameter of 4.8 mm (0.1889 in.).
(d)
Remove and deburr the scuff plates (3), (5) and (9).
EFF : ALL
53-15-15Page 406
(2)
Make the top coat of the scuff plates (3), (5) and (9) rough with scotch brite on an area of:
-15 mm (0.5905 in.) width on the scuff plate periphery,
-20 mm (0.7874 in.) radius around each fastener hole.
(3)
Clean the rough area with CLEANING AGENTS (Material No. 11-003) and MISCELLANEOUS (Material No. 19-003).
R NOTE : The correct application of the release agent makes sure that
____ R the scuff plates are not damaged during the subsequent removal R procedure.
(4)
Apply adhesive tape on the rough area of the scuff plates.
(5)
Apply a thin layer of SPECIAL MATERIALS (Material No. 05-013A) to the remaining inner areas of the scuff plates (3), (5) and (9).
(6)
Remove the adhesive tape from the scuff plates (3), (5) and (9).
(7)
Apply a thin layer of SEALANTS (Material No. 09-005):
-to the mating area of the scuff plates on the fuselage skin and - on the rough area of the scuff plates.
(8)
Put the scuff plates (3), (5) and (9) in position on the fuselage skin.
(9)
Install the cover strip (2), the screws (6), (8) and (1) with SEALANTS (Material No. 09-016), the washers (7) and the nuts (4).
(10)
Tighten the nuts (4) and the screws (1) , (6) and (8).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身1(117)
