(2)
Make sure that the access panel 825AR or 826AR is removed from the closed cargo door.
4. Procedure
_________ R **ON A/C 001-049, 053-099, 101-149, 201-299, 301-399,
(Ref. Fig. 402/TASK 52-35-13-991-002-A) R **ON A/C 051-052,
R (Ref. Fig. 402A/TASK 52-35-13-991-002) **ON A/C ALL
Subtask 52-35-13-420-052
A. Installation of the Proximity Switch 5MJ or 12MJ
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
1EFF : ALL 1 52-35-13Page 415 1 1 May 01/05 1 1 1CES 1
(3)
Make sure that the electrical connector (1) is in the correct condition.
(4)
Install the proximity sensor on the cargo door structure as follows:
(a)
Put the proximity sensor (3) on the bracket (4) and attach it with the screws (2).
(b)
Remove the blanking caps from the electrical connector (1) and from the receptacle of the proximity sensor (3).
(c)
Connect the electrical connector (1) to the proximity sensor (3).
(5)
Install the target on the control lever as follows:
(a)
Set the target (7) on the control lever (6) so that the distance to the proximity sensor (3) is between 1.55 mm (0.0610 in.) and
2.05 mm (0.0807 in.).
(b)
Install the bolts (5), the washers (8) and the nuts (9) on the control lever (6).
(c)
Measure the distance between the target (7) and the proximity sensor (3) again.
(d)
If necessary, adjust the position of the target (7) so that the distance is correct.
(e) Tighten the nuts (9). Subtask 52-35-13-720-052
B. Do a functional test to make sure that the proximity switch 5MJ and/or 12MJ operates satisfactorily (Ref. TASK 52-35-00-720-001).
5. Close-up
________ Subtask 52-35-13-865-053
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1MJ
R 1EFF : ALL 1 52-35-13Page 416 1 1 May 01/05 1 1 1CES 1 Subtask 52-35-13-410-051
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Make sure that the applicable cargo door is correctly closed (Ref. TASK 52-30-00-860-002).
(3)
Install the access panel 825AR or 826AR> as required.
(4)
Remove the access platform(s).
R 1EFF : ALL 1 52-35-13Page 417 1 1 May 01/05 1 1 1CES 1R **ON A/C 001-049, 101-105,
TASK 52-35-13-000-003
Removal of the Limit Switch 2507MJ
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 2.10 m (6 ft. 11 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-52-22-000-001 Removal of the Ball Mats and Ball Strips 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-35-13-991-003 Fig. 403
3. Job Set-up
__________
Subtask 52-35-13-010-054
A. Get Access
(1)
Open the FWD or AFT cargo-compartment door and install the actuator safety locks (Ref. TASK 52-30-00-860-001).
(2)
Put the access platform in position for the applicable cargo compartment door.
R 1EFF : 001-049, 101-105, 1 52-35-13Page 418 1 1 May 01/05 1 1 1CES 1
(3) Remove the ball strips and the ball mat to get access to the limit switch of the door sill latch (Ref. TASK 25-52-22-000-001).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(97)
