(5)
Remove the screws (12) and the washers (13) from the riveted angle (14).
(6)
Carefully remove the handpump (16) through the cut out of the ground service panel (15).
(7)
Disassemble the hand pump (16) as follows:
(a)
Remove the plug (18) together with the O-ring (17) from the port B of the handpump (16)
(b)
Remove and discard the O-ring (17) from the plug (18).
1EFF : ALL 1 52-36-11Page 403 1 1 Feb 01/98 1 1 1CES 1
Hand Pump 3009GM
Figure 401/TASK 52-36-11-991-001
1EFF : ALL 1 52-36-11 Page 404
1 1 Feb 01/98
1 1
1CES 1
(c)
Remove the union (10) together with the O-ring (11) from the port C of the handpump (16).
(d)
Remove the union (5) together with the O-ring (4) from the port A of the handpump (16).
(e)
Remove and discard the O-rings (4) and (11) from the unions (5) and (10).
1EFF : ALL 1 52-36-11Page 405 1 1 Feb 01/98 1 1 1CES 1 TASK 52-36-11-400-001
Installation of the Hand Pump 3009GM
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container
No specific scraper
No specific warning notices
R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 02-003 F NSA 307110 TYPE 4
HYDRAULIC FLUID (PHOSPHATE ESTER BASE)
(Ref. 20-31-00)
Material No. 05-002 USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00)
Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A
CORROSION INHIBITING BRUSH CONSISTENCY
(Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
1EFF : ALL 1 52-36-11Page 406 1 1 May 01/05 1 1 1CES 1
C. Expendable Parts -------------------------------------------------------------------------------
FIG.ITEM --------- |DESIGNATION ------------------------------------ |IPC-CSN----------------------------------
4 O-ring 52-36-04 03 -140
11 O-ring 52-36-04 03 -160
17 O-ring 52-36-04 03 -180
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-00-00-864-001 29-00-00-910-002 29-10-00-863-002 29-14-00-614-001 29-14-00-614-002 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance ActionSafety Procedures of the Hydraulic SystemPressurize the Yellow Hydraulic SystemDepressurization of the Hydraulic ReservoirsPressurization of the Hydraulic Reservoirs through the Ground Connector
29-23-00-860-001 29-23-00-860-002 51-73-00-200-001 52-30-00-860-002 52-30-00-860-003 52-30-00-860-004 52-36-11-991-001 Disconnection of the Isolation Coupling of the Power Transfer Unit (PTU)Connection of the Isolation Coupling of the Power Transfer Unit (PTU)Inspection of Minor Damage to Aluminum CladdingClose the FWD or AFT Cargo-Compartment Door with the Yellow Electric PumpOpen the FWD or AFT Cargo-Compartment Door with the Hand PumpClose the FWD or AFT Cargo-Compartment Door with the Hand PumpFig. 401
1EFF : ALL 1 52-36-11Page 407 1 1 Feb 01/98 1 1 1CES 1
3. Job Set-up
__________
(Ref. Fig. 401/TASK 52-36-11-991-001)
Subtask 52-36-11-860-052
A. Aircraft Maintenance Configuration
(1)
Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(111)
