(4)
Make sure that the Bulk door is opened (Ref. TASK 52-30-00-860-010).
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-31Page 409 1224-224, 228-228, 1May 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 221-221, 224-224, 228-228,
4. Procedure
_________ R **ON A/C 001-003, 051-054,
Subtask 52-33-31-910-050
A. Preparation for Installation
(Ref. Fig. 401/TASK 52-33-31-991-001)
(1)
Do an inspection of the component interface and/or the adjacent area. (Ref. TASK 52-33-11-200-001).
(2)
Clean the component interface and/or the adjacent area. (Ref. TASK 52-33-11-100-001).
(3)
Apply SEALANTS (Material No. 09-018) to the shanks of the bolts (1),(4).
(4)
Apply SEALANTS (Material No. 09-013) to the mating surface between the fitting assembly (6) and the Bulk cargo-compartment door.
Subtask 52-33-31-420-051
B. Installation of the Stop Fitting
(Ref. Fig. 401/TASK 52-33-31-991-001)
(1) Install the stop screw (6) as follows:
(a)
Assemble the stop screw (5) in the fitting assembly (6).
(b)
Adjust the stop screw to an initial gap of 5.0 mm (0.1968 in.).
(c)
Install the new lockplate (7) and the nut (8) on the stop screw (5).
NOTE : Do not torque and safety the nut (8) at this stage.
____
(2) Install the fitting assembly (6) as follows:
(a) Put the fitting assembly (6) in position at the bulk door structure and attach it with the bolts (1),(4) and the nuts (2),(3).
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-31Page 410 1224-224, 228-228, 1May 01/05 1 1 1CES 1
(b)
TORQUE the nuts (2) to 0.7 m.daN (61.94 lbf.in).
(c)
TORQUE the nuts (3) to 0.8 m.daN (70.79 lbf.in).
(d)
Apply a bead of SEALANTS (Material No. 09-016) at the edge of the fitting assembly (6) and the BULK cargo-compartment door.
Subtask 52-33-31-820-051
C. Adjustment Procedure
(1)
Adjust the skin offset between the fuselage contour and the BULK cargo-compartment door correctly (Ref. TASK 52-33-11-820-001).
(2)
TORQUE the nut (8) to between 2.0 m.daN (14.7492 lbf.ft) and 2.2 m.daN (16.2241 lbf.ft).
(3)
Safety the nut (8) with the lockplate (7) (refer to typical lockplate installation of Fig. 401A).
R **ON A/C 004-049, 055-099, 101-149, 221-221, 224-224, 228-228,
Subtask 52-33-31-910-050-A
A. Preparation for Installation
(Ref. Fig. 401A/TASK 52-33-31-991-001-A)
(1)
Do an inspection of the component interface and/or the adjacent area. (Ref. TASK 52-33-11-200-001).
(2)
Clean the component interface and/or the adjacent area. (Ref. TASK 52-33-11-100-001).
(3)
Apply SPECIAL MATERIALS (Material No. 05-002) to the shanks of the bolts (1),(4).
(4)
Apply SEALANTS (Material No. 09-018) to the mating surface between the fitting assembly (7) and the Bulk door structure.
Subtask 52-33-31-420-051-A
B. Installation of the Stop Fitting
(Ref. Fig. 401A/TASK 52-33-31-991-001-A)
(1) Assemble the stop screw (5), the washer set (6) and the nut (8) on the fitting assembly (7).
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-31Page 411 1224-224, 228-228, 1May 01/05 1 1 1CES 1
(2)
Put the fitting assembly (7) in position at the bulk door structure and attach it with the bolts (1) and (4) and the nuts (2) and (3).
(3)
Apply a bead of SEALANTS (Material No. 09-005) at the edge of the fitting assembly (7) and the BULK cargo-compartment door.
Subtask 52-33-31-820-051-A
C. Adjust the skin offset between the fuselage contour and the BULK cargo-compartment door correctly (Ref. TASK 52-33-11-820-001).
R **ON A/C 001-049, 051-099, 101-149, 221-221, 224-224, 228-228,
5. Close-up
________ R **ON A/C 001-003, 051-054,
Subtask 52-33-31-916-050
A. Protective Treatments
(1)
Apply a layer of STRUCTURE PAINTS (Material No. 16-003) to the seal around the fitting assembly (6).
(2)
Apply SPECIAL MATERIALS (Material No. 05-027) to all exposed surfaces which you touched or moved.
R **ON A/C 004-049, 055-099, 101-149, 221-221, 224-224, 228-228,
Subtask 52-33-31-916-050-A
A. Protective Treatments
(1)
Apply a layer of STRUCTURE PAINTS (Material No. 16-003) to the seal around the fitting assembly (7).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(71)
