(5)
Install the sleeves (5) and the springs (6),(7) to the bolts (8).
(6)
Install the bolt (8) and the washer (3) to the lower hinge bracket.
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-22Page 415 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(7)
Install the remaining washers (3),(4) and the nuts (2) to the bolts (8).
(8)
Tighten the nuts (2) and safety them with new cotter pins (1).
(9)
Install the springs (6),(7) to the spring bolts (21) and the fittings of the vent door frame.
(10)
Install the connection rod (13) to the vent door (10) as follows:
(a)
Put the connection rod (13) to the actuator arm and install the bolt (11) together with the washers (12),(15), the bush (14) and the nut (16).
(b)
Tighten the nut (16) and safety it with new cotter pin (17).
(11)
Put the cover assy (20) to the brackets of the cargo door and attach it with the bolts (18), the washers (19) and the nuts (21).
Subtask 52-32-22-710-050
B. Operational Test
(1)
Close the vent door of the opened AFT cargo door as follows:
(a)
Press the roller lever of the interlock mechanism outboards to release the blockage of the latching shaft.
(b)
Pull the door handle down to the locked position and push it into the recess of the door structure.
(2)
Make sure that the skin offset between the vent door and the cargo door contour is correct (Ref. TASK 52-31-11-820-003).
(3)
Make sure that the clearance between the stop bolts of the vent door and the related stops is correct (Ref. TASK 52-31-11-820-003).
(4)
Push the handle flap in and pull up the door handle to the unlocked position.
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-22Page 416 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
**ON A/C 051-052,
Subtask 52-32-22-420-050-A
A. Installation of the Vent Door
(1)
Put the vent door (10) in position to the vent door frame.
(2)
Install the bolt (8), the washer (3) and the bush (9) to attach the vent door (10) to the upper hinge bracket.
(3)
Install the bolt (8) and the nut (2) to attach the vent door temporarily to the lower hinge bracket.
(4)
Adjust the upper and lower gaps between the vent door (10) and the vent door frame as follows:
(a)
Put the vent door (10) in the middle of the opening so that the gap is between 1.0 mm (0.0393 in.) and 3.0 mm (0.1181 in.).
(b)
Measure the clearance between the lower hinge bracket and the lower hinge arm to get the thickness of the shim set.
(c)
Remove the nut (2) and the bolt (8) from the lower hing bracket.
(d)
Install the shim set of washers (4) with the correct thickness between the lower hinge brackets and the lower hinge arm.
(5)
Install the sleeves (5) and the springs (6),(7) to the bolts (8).
(6)
Install the bolt (8) and the washer (3) to the lower hinge bracket.
(7)
Install the remaining washers (3),(4) and the nuts (2) to the bolts (8).
(8)
Tighten the nuts (2) and safety them with new cotter pins (1).
(9)
Install the springs (6),(7) to the spring bolts (21) and the fittings of the vent door frame.
(10) Install the connection rod (13) to the vent door (10) as follows:
(a)
Put the connection rod (13) to the actuator arm.
(b)
Install the bolt (11) together with the washers (12),(15), the bush (14) and the nut (16).
1EFF : 051-052, 1 52-32-22Page 417 1 1 Aug 01/05 1 1 1CES 1 (c) Tighten the nut (16) and safety it with new cotter pin (17).
(11) Put the cover assy (20) to the brackets of the cargo door structure and attach it with the screws (18) and the washers (19). Tighten the screws (18).
Subtask 52-32-22-710-050-A
B. Operational Test
(1)
Close the vent door of the opened AFT cargo door as follows:
(a)
Press the roller lever of the interlock mechanism outboards to release the blockage of the locking shaft.
(b)
Turn the locking handle up to the locked position and push it into the recess of the handle flap.
(2)
Make sure that the skin offset between the vent door and the cargo door contour is correct (Ref. TASK 52-31-11-820-003).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(13)
