R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 503 1224-224, 228-228, 1May 01/05 1 1 1CES 1
Measurement of the Skin Offset
Figure 501/TASK 52-33-11-991-008
R 1EFF : 001-003, 051-054, 1 52-33-11Page 504 1 1 May 01/05 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1
52-33-11Page 505
1 1 Aug 01/98 1 1 1CES 1
Measurement of the Skin Offset
Figure 501A/TASK 52-33-11-991-008-A12 (SHEET 1)
R 1EFF : 004-049, 055-099, 101-149, 221-221, 1 52-33-11Page 506 1224-224, 228-228, 1May 01/05 1 1 1CES 1
Measurement of the Skin Offset
Figure 501A/TASK 52-33-11-991-008-A22 (SHEET 2)
R 1EFF : 004-049, 055-099, 101-149, 221-221, 1 52-33-11Page 507 1224-224, 228-228, 1May 01/05 1 1 1CES 1
Adjustment of the Skin Offset
Figure 502/TASK 52-33-11-991-009
R 1EFF : 001-003, 051-054, 1 52-33-11Page 508 1 1 May 01/05 1 1 1CES 1
Adjustment of the Lateral Gaps
Figure 503/TASK 52-33-11-991-003
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 509 1224-224, 228-228, 1May 01/05 1 1 1CES 1
(c)
Remove the nuts (5) and the lock plates (4) from the stop bolts (2). Discard the lock plates (4).
(d)
Turn the stop bolts (2) until they touch the stop fittings (3).
(e)
Set the Bulk door in the closed position and carefully move the locking handle in the locked position (Ref. TASK 52-30-00-860-008).
NOTE : If this is not possible, change the position of the
____ forward and aft latch spigots on the Bulk door frame (Ref. TASK 52-33-32-400-001).
(2) Measure the skin offset which should be out of the wind between the contour of the Bulk door and the fuselage.
NOTE : The lateral and the upper skin offsets must be between zero
____ and 2.0 mm (0.0787 in.). The lower skin offset in the scuff plate area must be between
1.0 mm (0.0393 in.) and 3.5 mm (0.1377 in.).
(3)
Adjust the lower skin offset as follows (refer to section E-E):
(a)
Open the Bulk door to get access to the lowest stop bolts (2).
(b)
Turn the two lowest stop bolts (2) on the lower stop fittings (3) counterclockwise.
(c)
Close the Bulk door and make sure that the lower skin offset is correct.
(4)
Adjust the upper skin offset as follows (refer to section D-D).
(a)
Remove and discard the cotter pin (10) from the damper housing (8).
(b)
Remove the nut (6) and the washer (7) from the damper housing (9) of the hinge arm (17).
(c)
Turn the threaded plug (8) clockwise or counterclockwise until the upper skin offset is correct.
(d)
Install the washer (7) and the nut (6) to the damper housing (9) and tighten.
(e)
Install the cotter pin (10) to safety the threaded plug (9).
R 1EFF : 001-003, 051-054, 1 52-33-11Page 510 1 1 May 01/05 1 1 1CES 1
(f) Apply STRUCTURE PAINTS (Material No. 16-003) to the surface of the damper housing (9).
(5) Adjust the lateral skin offset as follows (refer to the sections A-A and B-B):
(a)
Open the Bulk door to get access to the stop bolts (2).
(b)
Turn the other stop bolts (2) counterclockwise until they touch the related stop fittings (1).
(c)
If the lateral skin offset is out of tolerance, turn the stop bolts (2) clockwise.
NOTE : The clearance between the stop bolts (2) and the stop
____ fittings (1) must not be more than 0.4 mm (0.0157 in.).
(d) Close the Bulk door and make sure that the skin offset is correct.
(6) If the skin offsets are correctly adjusted, safety the stop bolts (2) as follows:
(a)
Install new lockplates (4) and the related nuts (5) on the stop bolts (2).
(b)
TORQUE the nuts (5) to between 2.0 m.daN (14.7492 lbf.ft) and 2.2 m.daN (16.2241 lbf.ft).
(c) Safety the nuts (5) with the lock plates (4). R **ON A/C 004-049, 055-099, 101-105,
Subtask 52-33-11-820-052-A
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(33)
