(2)
Make sure that the skin offset between the Bulk cargo-compartment door and the fuselage contour is correct (Ref. TASK 52-33-11-820-001).
(3)
Make sure that the Bulk cargo-compartment door closes easily.
(4)
Adjust the position of the forward and/or aft latch spigot as follows:
(a) Measure the clearance Z between the barrel locks of the locking mechanism and the latch spigot.
NOTE : The clearance Z must be min. 0.10 mm (0.0039 in.) .
____
(b)
If the clearance Z is not correct, adjust the position of the latch spigot with the related serrated plate (Ref. TASK 52-33-11-820-001).
(c)
TORQUE the nuts (10) and (28) to between 0.35 and 0.45 m.daN
(30.97 and 39.82 lbf.in).
(d)
TORQUE the nuts (11) and (29) to between 0.70 and 0.80 m.daN
(61.94 and 70.79 lbf.in).
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-32Page 412 1224-224, 228-228, 1May 01/05 1 1 1CES 1 (5) Adjust the proximity switch 50WV as follows:
(a) Measure the distance X between the target plate and bracket surface.
NOTE : The distance X must be between 44.2 mm (1.7401 in.) and
____ 44.8 mm (1.7637 in.).
(b)
If the distance X is not correct, loosen the nut (35) and adjust the proximity target (36) until the distance is correct.
(c)
Tighten the nut (35) and safety it with the new tab washer (34).
(d)
Install the proximity sensor (25) with the safety washer (23) and the nut (24) to the bracket of the aft latch spigot (27).
(e)
Safety the nut (24) and the safety washer (23) with lockwire, corrosion-resistant steel dia 0.6 mm (0.2362 in.).
(f)
Connect the connector of the cable loom (26) to the proximity sensor (25).
(6) Do an operational test to make sure that the function of the proximity switch 50WV is correct (Ref. TASK 52-71-00-710-001).
R **ON A/C 001-049, 051-099, 101-149, 221-221, 224-224, 228-228,
5. Close-up
________
Subtask 52-33-32-916-053
A. Protective Treatment
(1)
Apply a layer of SEALANTS (Material No. 09-016) to seal all nuts.
(2)
Apply a bead of SEALANTS (Material No. 09-016) around all nuts and the edges of the stop fitting (2).
(3)
Apply STRUCTURE PAINTS (Material No. 16-003) to protect the bead of the sealant.
(4)
Apply a protective layer of SPECIAL MATERIALS (Material No. 05-027) to all components which have no other surface protection.
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-32Page 413 1224-224, 228-228, 1May 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105,
Subtask 52-33-32-410-050
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
If removed, attach the insulation mats with VELCRO tapes and disc fasteners adjacent to the bulk door frame.
(3)
Install the floor panels 162HF, 162GF, 162KF and 162LF (Ref. TASK 53-22-14-400-001).
(4)
Put the protection cover (20) of the proximity switch 50WV with the plate (39) and the gasket (40) in the installation position.
(5)
Attach the protection cover (20) with the screws (21) and the washers
(21) on the Bulk door frame and the floor panel 162KF.
(6)
Install the sidewall panels 162BW and 162EW with the related quick-release fasteners.
(7)
Close the Bulk cargo-compartment door (Ref. TASK 52-30-00-860-008).
(8) Remove the access platform(s). R **ON A/C 106-149, 221-221, 224-224, 228-228,
Subtask 52-33-32-410-050-A
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
If removed, attach the insulation mats with VELCRO tapes and disc fasteners adjacent to the bulk door frame.
(3)
Install the floor panels 162HF, 162GF, 162KF and 162LF (Ref. TASK 53-22-14-400-001).
(4)
Put the protection cover (20) of the proximity switch 50WV with the plate (39) and the gasket (40) in the installation position.
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-32Page 414 1224-224, 228-228, 1May 01/05 1 1 1CES 1
(5)
Attach the protection cover (20) with the screws (21) and the washers
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門6(76)
