1EFF : ALL 1 32-21-00Page 405 1 1 May 01/03 1 1 1CES 1
Deactivation/Reactivation of the NLG Towing Attachement.
Figure 401/TASK 32-21-00-991-006
1EFF : ALL 1 32-21-00Page 406 1 1 May 01/03 1 1 1CES 1
NOSE GEAR - INSPECTION/CHECK
____________________________ TASK 32-21-00-200-002 General Visual Inspection of the Nose Landing Gear WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR.
_______
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice(s)
No specific access platform 2.06 m (6 ft. 9 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-12-32-611-001 Check Shock Absorber Fluid Level 12-14-32-614-004 Check Shock Absorber Charge Pressure 32-22-00-010-001 Nose Gear Doors - Ground Doors Opening 32-22-00-410-001 Nose Gear Doors - Ground Doors Closing
3. Job Set-up
__________ Subtask 32-21-00-860-056
A. Aircraft Maintenance Configuration
(1) On the panel 400VU:
-Make sure that the landing-gear normal control-lever is in the DOWN position.
1EFF : ALL 1 32-21-00Page 601 1 1 Aug 01/05R 1 1 1CES 1
(2) On the panel 110VU:
-Make sure that the free-fall control handle is in the usual position.
Subtask 32-21-00-010-053
B. Get Access
(1) Open the main doors of the nose gear (Ref. TASK 32-22-00-010-001).
(2) Put the access platform in position.
Subtask 32-21-00-941-056
C. Safety Precautions
R (1) Make sure that the GROUND SAFETY LOCK (D23080000) or PIN-NLG DOWNLOCK R SAFETY (MZ23080000) as an alternative is in position.
(2)
Make sure that the SAFETY PIN - NLG DOOR (98D32203502000) are in position.
(3)
Put warning notice(s) to tell persons not to operate the landing-gear normal control-lever.
4. Procedure
_________
Subtask 32-21-00-210-052
A. General Procedure
(1)
Examine the lubrication points. Make sure that they are clean and serviceable.
(2)
Examine the protective finish on the nose gear surfaces. NOTE : Repair the protective finish if it is damaged.
____
(3)
Make sure that all the components are correctly installed and safetied.
(4)
Make sure that:
-The hinge pins and the hinges are correctly installed and serviceable.
-There are no signs of unusual wear.
1EFF : ALL 1 32-21-00Page 602 1 1 Aug 01/05 1 1 1CES 1
(5)
Make sure that the safety devices (cotter pins, lockwashers, lockwire) are correctly installed.
(6)
Make sure that all the identification plates are applicable and correctly installed.
(7) Make sure that the bonding strips are in good condition. Subtask 32-21-00-210-059
B. Inspection of the NLG Uplock Assembly
(1)
Examine for shock damage to:
-
the hook of the uplock assembly,
-
the uplock roller on the drag strut.
(2)
Examine the mechanical controls of the uplock assembly. Make sure that they are correctly installed and serviceable.
(3)
Examine the uplock assembly. Make sure that:
-It is correctly installed.
-There is no structural damage. Subtask 32-21-00-210-060
C. Inspection of the NLG Drag Strut and Lockstay Assemblies
(1)
Examine the safety devices. Make sure that they are correctly installed and in good condition.
(2)
Examine the lockstay for signs of corrosion, cracks, distortion and wear.
(3)
Examine the protective finish on the surfaces.
Clean and repair the protective finish if necessary.
Subtask 32-21-00-210-061
D. Inspection of the NLG Downlock Release Actuator
(1)
Make sure that the downlock release actuator is correctly installed and safetied.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM LANDING GEAR 起落架3(60)
